Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Adjustable Height Infeed Table

Posts

Adjustable Height Infeed Table

#1

Adjustable Height Infeed Table

Dave Morris

>After making an outfeed table for my bandsaw (a few posts down the page), I quickly found out that supporting long odd-shaped pieces of wood by hand from the front of the band saw was "difficult" at best. I kept binding the blade, or changes in the wood's thickness meant the blade wouldn't cut a straight line as different parts of the wood registered off the short Kreg fence. A simple roller stand wouldn't work, since the wood was curved in both length and width, and some edges were very rough. Hmmm... gunna need an infeed table to control these curved wine vat slats.

Once again, shop space is at a premium, and if I can make something for one tool pull double duty on another tool, so much the better. Moving tipsy roller stands from place to place around my table saw is a dangerous dance, they are always in the way when not in use, and if not set to roll in a nearly perfect direction, they would bind the wood against the blade or fall over in mid-cut.... NOT good. So I decided to make a table that could be used on either end of my table saw (or on the side for cross cutting long stock or sheet goods), my jointer, my bandsaw, and also serve as a secondary odd-job table for "whatever".

"Project Priorities": Function, versatility, mobility, ease of construction, and utilizing whatever materials I had laying around the shop. Once again, my pack-rat tendencies came to the rescue, and I found all the major players in various rat-holes and sheet stock cut-offs. A few small bits of hardware were all I had to buy from the store. There's nothing like a new shop project to get rid of that piece of maple plywood you deemed unusable for a nice bathroom cabinet cuz it splintered so bad you couldn't drill a clean hole in it with your best brad point bits. (Grrrr...!)

First, the size of this table's top was determined by what was the left over from the piece of melamine I purchased for the band saw outfeed table. So a 16-1/2" wide by 39" long table top is the size I to which I matched the table's other components. I thought about the design, what I needed the table to do, and how I could use the materials at hand to make it all work. I had a piece of MDF that just fit the bill for the table's base, and a full set of old heavy-duty Darnell castor wheels for mobility--- two fixed, and two that were of the double-locking swivel variety. Okay, we're off to a good start.

A frame for the base was made from the last of the Sturdy-Floor scraps, and it straddles the bolts for the castor wheels. Problem... one of the bolts sticking through the base was in the way of the legs I planned to build. Changing that particular long bolt secured a hex-nut to a shorter bolt set in a T-nut fixed the problem. An outer set of 3/4" plywood legs was screwed and glued to the base frame, with an upper frame surrounding the legs for rigidity. An inner set of 3/4" plywood legs rests inside the outer legs, with an interior frame holding the inner legs together at their upper ends. A pair of crossbars straddle the inner frame at it's ends, and a piece of scrap ACX plywood between these crossbars gives the whole inner framework an "inner" table top and a strong anchor for stability. Matching 5/16" holes drilled in the legs every inch allow the finished table to be adjusted in height from 34" (just under table saw height), to over 53" (well over band saw height). Final height adjustment is done with carriage bolts seated in the crossbars, which support the melamine table top. Locked wing-nuts make decent handles to twist the carriage bolts using only my fingertips. Lifting the melamine top off the inner frame lets me use the ACX plywood "inner table top" at a table height equal to my jointer. Why my jointer? Well, I occasionally work with 10-foot (and longer) reclaimed lumber, and getting that first edge clean can be a real handfull on a 6" jointer.

A frame around the table top gives the melamine rigidity, and is sized to fit the crossbars front to back and side to side with about 1/8" of clearance. I placed a set of nail-in-place cushioned metal glides on the underside of the melamine where the carriage bolts contact it's surface, thinking it would reduce friction so turning the bolts by fingertip would be easier. They worked... in fact, they worked so well I had to add a couple pan-head screws to the crossbars to take up the slight amount of slack I planned in the top's fit, since it moved back and forth with the touch of a finger.

Problem-- my shop floor isn't perfectly flat everywhere, and we all know what happens when four contact points are not all in the same plane... wobble. For those locations where one of the four castor wheels isn't touching the floor, I added another carriage bolt through the MDF base, located between the swivel castors, to give the table an additional adjustable "foot". A crutch tip slipped over the end of the carriage bolt gives it a good bite on the cement to help prevent table movement.

The table isn't too hard to adjust, just lift the inner frame as high as needed and stick a 1/4" bolt through one of the matching holes in the inner and outer legs as they line up. A single bolt will keep the table from dropping, sticking one in each leg keeps the table from "tweaking" when a load is placed on top. The weight of the top keeps the bolts in place, so I don't have to worry about fitting a nut on all the bolts each time I change the table's height. I'll scribe lines on the legs to correspond with the height of each tool, to make setting the right table height for each tool less of a shot in the dark. I admit tossing around ideas for lifting the top by means other than muscle. The first thing that came to mind were those little pneumatic lifts used for car hoods and/or a camper shell's glass "win-door", but couldn't find any with enough travel to match the table's full range of adjustability. I also considered a system of pulleys, cables, and springs to bear the top wieght, but didn't want to get too complicated, or spend a lot of time/money on a simple shop table.

The space between the lower table legs is a prime candidate for storing "something", and I'm thinking a set of those multi-drawer nut/bolt/widget storage boxes from Wally World might be just the ticket. We'll see how that pans out before the next project starts.

Again, this is a quickly built shop table, not fancy wood work. Screws, bolts, or butt-joints dripping Tight Bond hold everything together. It ain't pretty, but I gotta admit, using up some of the left-over stuff cluttering the shop is a thing of beauty. So far, I'm happy with how it has filled the "Project Priorities". However, your thoughts and advice on how I could do a better job next time are welcomed. I'm always willing to learn from my mistakes, even if someone else has to point them out. ;-)

Below is a pic of the table set for the Table Saw.

Dave


img

Re: Adjustable Height Infeed Table

#2

Table Set for the Band saw

Dave Morris

>Here the table is set up as in infeed for my old Jet 14" band saw.


img

Re: Adjustable Height Infeed Table

#3

Inner Frame Minus The Top

Dave Morris

>Gotta love those little hand clamps for keeping stuff in place during the construction phase.


img

Re: Adjustable Height Infeed Table

#4

Inner Top and Cross Bars

Dave Morris

>Here you can see how the carriage bolts stick through the cross bars and support the final melamine top. These bolts allow the melamine top to be adjusted for height and parallelism to the tool despite variances in the concrete floor.


img

Re: Adjustable Height Infeed Table

#5

Infeed and Outfeed Combined

Dave Morris

>Here is a pic of the final completed project, Infeed and Outfeed support of long, irregular stock on the band saw. I clamped a long temporary fence spanning both tables to give it a try. The result, full stock support during the entire cut, with minimum weight being carried by the saw's "pot-metal" table trunions. (I don't want to risk breaking those, I can't get new ones.)

Thanks for looking,

Dave


img

Re: Adjustable Height Infeed Table

#6

Well done!

Dominic Greco in Richboro PA

>Dave,

Excellent project! Or should I say "projects"? Cause the BS outfeed table goes with this like peas and carrots. You've put a lot of time and effort into hashing out the details and I can really appreciate that.

I have always loved milling up logs into lumber. But I too had a huge problem supporting hard to handle blanks at the bandsaw. This and the BS outfeed table are two projects that have been on my list for a long time!

Great job!

See ya around,

Dominic

Re: Adjustable Height Infeed Table

#7

Thanks, Dom

Dave Morris

>About the only thing I didn't worry about for either table was a miter slot. I don't need it for the band saw right now, and the motor on my contractor table saw interferes with placing a table next to the outfeed side of the saw.

As an aside, I found a good deal on an old Delta 6" jointer with a 2 HP motor. I don't need another jointer, but it works perfectly, and may use it to clean up the rough edges of some wood before ripping to width on the BS. Then I think I'll be looking closely at your write-up on a 2 HP upgrade to your BS --- nice job!

Dave

Re: Adjustable Height Infeed Table

#8

A 6" Jointer with a 2HP motor!?

Dominic Greco in Richboro PA

>Dave,

Wow! Talk about over-powered! I think the max I've ever seen is 1 1/2 HP. But still, that extra umph can't hurt! :>)

A jointer is the perfect companion to a bandsaw. The next thing you need is a surface planer (unless you already got one).

I'm not sure if you mentioned this or not. But did you ever change out the factory pulleys on you BS? The best thing I ever did was replace those cheapo cast aluminum sheaves (pulleys) on my Jet 14" BS with machined cast steel pulleys. Between that and the link belt I was amazed at how much smoother the saw ran.

See ya around,

Dominic

Re: Adjustable Height Infeed Table

#9

Ummm... well, it's like this...

Dave Morris

>Dom, the motor is not original to the jointer. The jointer is a 1948 Delta/Milwaukee 6" shorty (32" total bed length), with Rockwell serial number 67-4240. Nice little pup, and it's in perfect working order. The motor is a Dayton 115v/208-230v, 2HP, 3450 RPM, don't know how old (1-30 years?). The jointer came mounted on a home-made stand with locking casters, with a nice little 18" roller to put on whichever side you need. I figured (guessed?) the $80 asking price was at least half of what the motor alone would cost new, and the jointer/stand/roller was a nice bonus. ;-)

I already have more jointers than I can use: my original DJ-15, then another 1949 Delta 6" shorty with a 1 HP repulsion/induction motor on the factory metal stand, and finally a 7-1/2 foot long, 12" wide Superior Woodworking Machines "mothership", with four-corner adjustable tables, and of early 20th century vintage (it works fine but is awaiting a full resto just for "purty"). Not bragging, things just kinda happened that way, and I didn't want these fine old tools to go to a scrap yard. But toss in a few other old machines awaiting the dream shop I plan to build in a couple years, plus all the other tools and stuff most of us have in a home workshop, and you can begin to see why my garage is so crowded.

I think I'll match this new shorty with a 1948 Delta tilt-table saw that's sitting all by itself on it's combo saw/jointer stand, awaiting a partner for it's original dual-tool motor. They'll both be happy together, and I know my Jet BS is already salivating for that 2 HP Dayton.

Oh, and, nope, I haven't replaced the pulleys on the Jet yet. Tool things kinda took a back seat as my FIL's cancer progressed, and I'm just now getting back into the shop. Don't worry though, if there was any doubt before, you've convinced me--- they're on the "To Do" list. Besides, I'll have to change the pulley on the Dayton to compensate for the Jet motor's lower RPM difference, anyway. Might as well match it with a new one for the bandsaw, right? ;-)

Dave