Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Performax drum sander - kitchen cabinet making

Posts

Performax drum sander - kitchen cabinet making

#1

Performax drum sander - kitchen cabinet making

Dan Manturi

>Greetings. I am in a position where I can purchase a used Performax 22-44 Pro. This is a lot bigger than the 16-32 or regular 22-44. Not a small piece of equipment from a shop space perspective. I am also going to be helping my stepson redo his kitchen and then I plan on redoing my kitchen. I have never used one of these tools but I can potentially see that, at least during the making of my cabinets (I plan on making then from maple) and re-doing his cabinets (Beautiful Mahogany plywood with a very thick top surface veneer), this tool may be invaluable and not only worth buying but worth jockeying around in the shop for a while. It is on casters.

Comments welcome from owners / users of this tool.

Dan M.

Re: Performax drum sander - kitchen cabinet making

#2

Re: Performax drum sander - kitchen cabinet making

David Yoho

>Dan, as long as the price is affordable, I'd say why not. I'm guessing you already know what to expect and not expect from one of these. I think it will help speed up certain aspects of your cabinet projects. If the space requirement is too much of a problem, you could buy it, use it for your intended projects, and sell it afterward.

David

Re: Performax drum sander - kitchen cabinet making

#3

Re: Performax drum sander - kitchen cabinet making

Dan Manturi

>Yes, buy, use, sell is what I am thinking about. I never used one. Read reviews and most folks like them for flat panel work. Looking for a little "is the functionality worth the space commitment". I can get it for a decent price.

Re: Performax drum sander - kitchen cabinet making

#4

Re: 22-44Pro Thoughts

Mark Mandell - Gone Round In Jersey

>Had my 22-44Pro for about 6 years. Saves huge amounts of time in stock prep. Don't however, buy into the "abrasive planing" routine with 36 grit belts. It puts very deep scratches in the wood that then take too much wood off to remove. Hog your rough-cut stock flat on the planer. My workhourse grit is 80. For veneer, nothing courser than 220. Remember, the published tolerance across the cantalevered 22" drum is 1/100". Doesn't sound like much until you go through the veneer on one end. DAMHIKT |;-}}

It is, after all, a sander, thus do not try to take too much off at one pass. Start the conveyor with the drum off, put your board on and feed it, then bring the table up until the drum just starts to turn from contact with the wood; that'll be your starting point. Let the wood clear before turning on the drum, then adjust the height with taps. You'll learn to play the feed rate off against the grit and amount stock in contact. If you stall the drum by taking too much or feeding too fast, hit the drum kill switch immediately or it will blow the circuit breaker. Clean your belt often with a gum rubber block during use. If you let the abrasive get loaded, it'll burn lines in your wood. Be careful to keep the conveyor running true with the tensioners on the outfeed end; usually just a touch of tightening is enough to correct the tracking.

Oh, you DO have a dust collector with 4" (min) lines, right? No shop-vac will handle the amount of dust this thing generates.

Re: Performax drum sander - kitchen cabinet making

#5

Re: 22-44Pro Thoughts - Thanks -good input!

Dan Manturi

>Thanks! This detail is what I needed to know. 220 grit on veneer. Yes, I do have a dust collector. Just need to run my 220 line to hook that up, which I will be doing shortly.

Thanks for this information.

Dan

Re: Performax drum sander - kitchen cabinet making

#6

Re: 22-44Pro Thoughts - Thanks -good input!

Barry Irby

>I have a 16/32 and agree with everythng Mark said. I would second the thing on dust collection. The fines porduced by sanding at this scale clog the filter bag on my (non-cyclone) DC. I take the bag off and turn it inside out and shake it out. (An amazing dust explosion, so do it on a windy day with your back into the wind.)

I also agree about the grits. I have not done a lot with trying to remove finish, so if your son's cabinets are already finished, don't be surprised if the belts clog almost instantly. I have been running some heart pine through mine and the belts clog quickly. I have been cleaning them by soaking them in Simple Green solution and using a nylon brush. Works great. My belts are about $8 each and I'm a tight wad. Can't stand the idea that an $8 belt would only last 5 minutes. I let them sit in the cleaner for a while and it take about five minutes to run water over them and scrub them. Then hang them up to dry. Don't know if Simple Green will work as well on "finish" clogged belts.

I have a very small shop and find that Performax is worth the space. It will sand difficult woods the planer would destroy. I have mine on a low stand and it parks under the wing of my TS.

Re: Performax drum sander - kitchen cabinet making

#7

An alternative

Bill Tindal, E.TN

>I have not owned a drum sander so I can not make a comparison. I have a large air compressor and an air driven disk sander. These air driven sanders don't leave swirl marks. With a coarse grit they remove wood as fast as my belt sander, which I don't need to use any more, and with a fine grit they finish sand ready to apply finish. I suspect you would find the air driven disk sander more versatile, and nearly as fast for panels.

Re: Performax drum sander - kitchen cabinet making

#8

While we're talking about the 22-44... a problem

doug f, san clemente, ca

>I've got a relatively new 22-44, about a year, and when I'm sanding for awhile, say about 10-15 minutes, the bearing nearest the piller starts to howl. Still works fine and stops when I let it cool for 1/2 an hour or so, but it just doesn't sound like it should be doing that.

Anyone have a similar problem?

Thanks.

Doug

Re: Performax drum sander - kitchen cabinet making

#9

Re: An alternative

Barry Irby

>Bill, I don't own a large Air Compressor, but I do own a five inch electric ROS. If the Air version is as much of an improvement over the ROS as the ROS is over a pad sander, I have no doubt it is a very powerful sanding tool. To me, The ROS is amazing and nearly as aggressive as a Belt Sander and leaves a fine finish.

My only reservation about what you say is that the Performax type drum sander will sand flat panels and keep them flat. With care it does it consistently and practically on "Auto Pilot". Just get into the rhythm, find the right grit and belt speed and pass them through. The panels come out consistently the same thickness and flat as well as smooth. With a ROS or An air driven ROS I would think you would have trouble achieving that level of "flatness" and maintaining it. Don't get me wrong, I have a 16/32 drum sander and wish I had the big air compressor and sander.

Another choice would be to take the panels to a cabinet shop and pay them to run them through their big belt sander (day timer, time saver?). I used to do that and have to admit I am glad I don't have to make that run anymore.

Another question might be, which would you rather have when the job is done, a big Air Compressor and a sander or a 22/44pro? (And don�t even consider running an air sander on anything less than a really big air compressor.)

Re: Performax drum sander - kitchen cabinet making

#10

couldn't live without mine

Mark Valsi

>

Re: Performax drum sander - kitchen cabinet making

#11

My Experience......

Bill Tindal, E.TN

>I have prepared hundreds of panels for doors, table tops and case goods and never saw the need to own a drum type sander, or suffered a significant variable thickness problem. . However, when I re-saw veneer I take the pieces to a friend who sands them with his drum sander. And if I was running a cabinet shop or re-sawed much veneer, I would most certainly have a drum sander.

I think the light weight factor of the air driven sanders may make them easier to control, vs the electric versions. It is a one handed operation with little effort.

Re: Performax drum sander - kitchen cabinet making

#12

Re: couldn't live without mine

Stuart Hough

>Never used one, but I am lusting for one, either 16/32 or 22/44. It just makes sense, not to mention a LOT easier!

Re: Performax drum sander - kitchen cabinet making

#13

Re: Cleaning Abrasives

Mark Mandell - Gone Round In Jersey

>I soak mine in Simple Green and scrub them a bit, rinse well, and hang (with weight) to dry. However, once you start getting burn marks, oven cleaner will be needed to get "most" of it off. You'll also have to pick off the resin, bit-by-bit. Anything left on the belt will just start a new streak pretty quick, and then you'll be going for a new belt (hey, they don't last forever). Be specially wary of pitchy/sweet woods like cherry and maple and the softwoods like fir and spruce.

good machine; plays nice.

mm

Re: Performax drum sander - kitchen cabinet making

#14

Re: While we're talking about the 22-44... a probl

Mark Mandell - Gone Round In Jersey

>Bearing's fried. 1 year? it may be covered. Call jet service.

GL

Re: Performax drum sander - kitchen cabinet making

#15

Re: Performax drum sander - kitchen cabinet making

Dan Manturi

>Lots of great info here, as usual. I have used my PC and Dewalt ROS sanders a lot, but on these veneer cabinets, I do not want to risk a thin spot and there are a lot of doors to do.

The statement that the sander takes up a lot of room but is worth it was important to me as well, I can imagine using this on highly figured woods like curly maple, which does not joint or plane real well.

Washing sandpaper, new one to me. But it seems like a popular activity based on this thread. I also plan to clean up the doors first with some TSP and 000 scotch brite pads. Hopefully I can get some of the gum off that way. Got to go light with that, though.

Thanks again.

Dan M

Re: Performax drum sander - kitchen cabinet making

#16

Re: I could, and did

Glenn Madsen near San Francisco

>I fought with my 16/32 for 4 months, and finally sold it in frustration. It wasn't close to autopilot on the woods I was using, and not nearly fast enough to justify the space in my garage/shop.

So it went to someone who wanted it. I use other sanders, the planer I have, and for smaller work, a growing collection of handplanes.

It's a decent machine, just not perfect. YMMV

Re: Performax drum sander - kitchen cabinet making

#17

Thanks Bill, good to know what really works....

Barry Irby

>

Re: Performax drum sander - kitchen cabinet making

#18

Re: Performax drum sander - kitchen cabinet making

Barry Irby

>If I were going to run finished stuff through mine, I would clean it first (probably not really, but I would like to think I would) and use about an 80 or 100 grit belt and set the machine to take an extremely light cut and use a high rate of feed. Trying to knock off just the finish and not build up much heat.

One thing I think I have learned is that you should use a light cut and fast feed rate. You must keep the work moving. Slow feed rate or stalling will cause burns on the wood and perhaps scallops.

Changing the belts is something of a knack. Took me a while to develop the strength in the "social" finger on my left hand. The clip has sort of a two stage or double action. I pull it all the way up, compressing both functions, insert the end of the belt and release the clip in such a way that it grabs the end of the belt first and then pulls the belt tight. I find it useful to crease the belt where it makes the bend to go into the drum. (This may make more sense once you try it) I used to really struggle, but now it seems easier or at least logical.