Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

How would you cut this?

Posts

How would you cut this?

#1

How would you cut this?

lee beeden

>OK I'll try to explain this as best as i can.

Two walls meet in a room at a 90 degree angle( or close to that)

Lady wants a computer desk at 42" so she can stand and work

the run is 6' 7" on each wall meeting with a 45 degree cut.

The desk is around 18" deep so it is to long to cut the mitre on my 10" sliding chop saw.

how do i cut the mitre so it looks like a picture frame when it comes together? i want it to look good!!

not sure about the table saw, perhaps that's the way?

and also how do i make this joint strong?

perhaps a butterfly..............never done it before got to start somewhere!!!!

and just in case you were wondering if the walls are not at a true 90 to each other I'll hide it with moulding.

Thanks in advance for your input

Lee

Re: How would you cut this?

#2

Dale Lenz

Re: How would you cut this?

Dale Lenz

>Assuming you are using plywood or something similar for the table top. I'd go with your suggestion of using the table saw, might need to turn your miter gage backwards or build a miter jig for TS. Have several inches of extra length for getting the joint just so.

As far as strengthening the miter, the first thing that comes to my mind is a spline of say 1", 1/2" per miter side. On second thought: do a blind spline using 1/4" plywood for the spline wood, ie stop the mortise of the spline joint prior to exiting the table top.

Re: How would you cut this?

#3

Re: How would you cut this?

Bob McGovern

>Hi, Lee. First you might use a couple scrap sticks to make an angle jig for the corner, see how close to 90 degrees it is. Screw em together like a bevel gauge. Rough cut pretty close to 45 degrees, wrong side up with a Skill saw, just outside the line. Then you finish up with a router, if you have one. Either a straightedge offset accurately from the cut line, or a straightedge directly ON the cut line & use a flush trim bit. It you want a really perfect match, line up the two cut halves exactly to match your wall-angle template (as they will be installed, i.e.). But leave a gap just under 1/2" between the joint halves. Then run a router & 1/2" bit on a straightedge down the gap -- ensures perfectly mated pairs, with any errors cancelling out.

As for joining, biscuits aid in alignment & prevent shear; dowels can work if accurately drilled. You can find at many hardware stores special "cross bolts" for seaming formica countertops, or get them from Rockler. They draw the joint together very tightly. Two should do. Then, to be extra paranoid, you could screw on a couple cleats spanning the joint underneath. That'll hold er.

Re: How would you cut this?

#4

Re: How would you cut this?

Barry Irby

>Shops that make kitchen counter tops do it all the time. You might check around and see if you can find a friendly local shop that would cut it for you if you don't feel up to the task or don't have the right equipment.

Re: How would you cut this?

#5

I like this suggestion

Bill Tindal, E.TN

>Especially if you don't have the equipment or experience to do it yourself. These sorts of things I rough cut by any means and then trim to fit with the jointer.

If you get the miter right you can always scribe the sides to fit the wall perfectly.

Re: How would you cut this?

#6

Re: How would you cut this?

M. McNamee

>That is method I used in making a friends countertop that had a 90 degree turn. Worked great and the joint was tight, no gaps.

Re: How would you cut this?

#7

Re: How would you cut this?

Johanna

>I agree with Bob - rough cut, then clean up with a router. I just finished a desk that wraps around 3 walls of my little office room. Here are pictures: http://home.comcast.net/~thompsonjo/Office.htm.

The three pieces of the desktop are pulled together with tite-joint clamps. I bought mine from Woodworker's Supply, but any place that sells to cabinet shops would have them.

The longest wall had a significant bulge, so I made a template for it, then routed that edge of the desk top to fit. The center desk top was cut about an inch oversize so I'd have some room to adjust it to fit the two side sections.