Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Resawing info?

Posts

Resawing info?

#1

Resawing info?

Paul Woolson

>Hi all. I'm looking at getting 4 billets of Cocobolo resawn. My 17" jet just isn't accurate enough (or maybe it's the opperator)to put that kind of expensive wood into. Does anyone know of a good (and I mean GOOD) resawer in the midwest? If it's taboo to post here, please email me. Thanks, Paul

Re: Resawing info?

#2

Re: Resawing info?

Patrick Schupbach

>What blade are you running on your saw? A good blade could make a big difference. Timberwolf, Woodslicer are two good ones. Hope this helps.

Re: Resawing info?

#3

Re: Resawing info?

Paul Woolson

>I am using a 1" Timberwolf blade.

I'm pretty confident cutting up most wood to my desired thickness (.120 spruce, .110 mahogany, etc. ) but this stuff is outrageously beautiful, and expensive. I really don't want to screw it up.

Re: Resawing info?

#4

Re: Resawing info?

Falberg saw Co

>How deep are you cutting?

Re: Resawing info?

#5

Re: Resawing info?

Paul Woolson

>Deep? Not sure what you mean by deep.

The slabs are 9"x24"x2" and I want .110" slices off of them.

Re: Resawing info?

#6

Re: Resawing info?

Curly Smith

>No offense intended but I think you'd be better of buying some thin lumber or veneer and saving your piece until you're comfortable resawing it. All of these have 1/8" Cocobolo

Rockler Cocobolo Thin Lumber

Exotic Woods

Constantines Hardwoods/Lumber 1/8" Thin Woods

If you do a search on 'Cocobolo "thin lumber" OR veneer' and your area you might find a local supplier. Or, call up this page and add the additional search terms: Search Terms

Re: Resawing info?

#7

Re: Resawing info?

Paul Woolson

>This is all flatsawn lumber and most in widths from 3-6" so it won't work for me. Just curious why I would be better off in your opinion buying pre cut lumber than having the lumber I have cut?

Re: Resawing info?

#8

Re: Resawing info?

Falberg saw Co

>Do you want veneer to be 2"Wide x X" Long, 9"Wide x X Long", or 24"Wide x X" Long? The depth of the cut would determine the Width of the veneer. I would prefer the 24" wide but not sure if your saw is big enough. If you're wanting the 9" wide veneer it would be easy with any saw as long as you use a blade with enough set to keep a flat kerf. A Timberwolf 3/8" - 3TPI blade should do nicely. I wouldn't try it with any of the carbide or narrow-kerf blades unless you're set up to run incredible tensions. A 3/8" - 3TPI would cost .060" of dust for each cut but you'd save $X on re-sawing service if you outsource the cutting (that can be as expensive as the wood itself) Feed it in slowly and you can sand the track marks down (without having to plane off the "drift" error; which is also expensive). I've got a blade that will cut 24" flat but I'd have to build another custom saw to run it 24" deep. I did one a couple years ago to cut 22" and it worked fine.

Re: Resawing info?

#9

Re: Resawing info?

Curly Smith

>I should have included my reasoning in the post:

I have serious doubts that you'll be able to find somebody to cost effectively resaw your wood. Of course with the chunk of wood you're talking about, cost effective is a very relative term.

Your hesitation in doing the job yourself stems, quite naturally, from the high cost of the wood. A mistake could be very costly but it might not cost more than outsourcing the job. After all, you're not going to ruin the entire slab with a mistake. Do you have a copy of the Duginski bandsaw book and have you setup your bandsaw along his recommendations? With a properly tuned bandsaw, the right TPI blade, and some patience I'm sure you'd do fine. Practice on some 2x12's until you're comfortable and the cuts are accurate.

FWIW, my resawing errors arise primarily from a feed rate that's too high.

Re: Resawing info?

#10

If you have a tablesaw

Curly Smith

>If you have a tablesaw you can greatly reduce the possibility of resaw error at the expense of turning more of your wood into sawdust.

Assuming you have a tablesaw or access to one:

Install a thin kerf blade

Adjust the fence to the proper width

Run your block through, flip it over and run the other side through. You'll want to set the blade height to leave ~1" in the center.

Turn the block around and cut the other side

Move the fence over and repeat the process until you've "scored" the entire block. It might be useful to insert plywood shims between the fingers to keep the block rigid.

When you've finished on the tablesaw you can complete the cuts on your bandsaw or with a handsaw. You'll turn more of your Cocobolo into sawdust this way than you would by just using the bandsaw but your chances for error are almost zero.

Re: Resawing info?

#11

Re: Resawing info?

Wayne Stump

>I would echo Curly's advice--tune up your band-saw, and feed s-l-o-w-l-y! A couple years back, I received some excellent instruction on tuning and using a band saw from Michael Fortune. He uses 1/2", 3 tpi skip tooth inexpensive blades and makes sure they are sharp He also adjusts the upper wheel so that the tracking is parallel to the miter gauge slot and feeds very slowly. I tried it and it works! He has written instructions on how to do this in one of FWW past issues and I think that it is also available in one of the soft-cover publications that is a compilation of some related articles. It's well worth the trouble to find it and I'll look further to see if I can locate the article.

Good luck.

Re: Resawing info?

#12

Re: Resawing info? *LINK*

JohnM in Mid Mich

>Well, here's an answer to your original question "anybody know of a resaw mill in the midwest?" I've had various custom surfacing/edging/resawing done by Johnson's Lumber in Charlotte, Michigan. Resawing is $.40/bd ft, at 100 ft minimum. Real nice folks to work with. No other connection. I've linked a picture of their machine area from their web site.


img

L.L. Johnson Lumber Mfg. Co.

Re: Resawing info?

#13

WOW - Your Guitars! *LINK*

JohnM in Mid Mich

>Holy Cow! On a hunch I surfed to the domain in your email address. Very excellent stuff (and a beautiful web site). Wish I could afford one - maybe some day for my son, who plays way better than me anyhow...


Woolson Soundcraft