Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Miter Saw Stands...

Posts

Miter Saw Stands...

#1

Miter Saw Stands...

Rob Hix - King George, VA

>Hey all,

I have been doing some shop organization and turn around and have decided to put my miter saw on a contractors type miter saw stand. One reason is that I find myself using it more and more away from the shop, and second is that I hardly use it in the shop except to break down rough lumber from time to time. I use the tablesaw for all accurate cuts.

I have narrowed my selection down to two models. I will either get the Ridgid Miter Saw Utility Vehicle, or the Delta 36-136 stand. Does anyone have any experience with these two stands? I would appreciate some opinions from actual users.

Thanks in advance,

Rob Hix

Re: Miter Saw Stands...

#2

Re: Miter Saw Stands...

David Mathias - Central OH

>I don't have experience with either of those stands but I'm curious how you decided on them. I've been looking at them and had decided on the HTC PM7000. It gets great reviews on Amazon.com. I'd appreciate your insight.

David

Re: Miter Saw Stands...

#3

Re: Miter Saw Stands...

Rob Hix - King George, VA

>David,

First and foremost I wanted something mobile with more of a 2-wheel cart design. I started doing research and came across these two that met that criteria. From looking at the review of the HTC unit you mentioned, the one thing that was a consistent complaint was the one-wheel design.

Also, I preferred a unit in which I did not have to support much of the weight of the saw while setting up the legs. It appears on the HTC that you must pick up one end to fold out the legs. This is something I do not want.

I would also like something I can pick up locally as several friends and I have had extremely bad luck ordering things from Amazon. I try not to do business with them if I can help it. I can get the Delta unit at Lowe's and can possibly get the Ridgid unit at a local store although it would probably have to be ordered.

The two that I picked out according to the reading I have done set up and take down within seconds, and they have a gas cylinder to assist in the set up and take down.

Right now I am leaning toward the Delta since it is in stock at our Lowe's and I will not have to go through the hassle of ordering.

Hope this helps,

Rob Hix

Re: Miter Saw Stands...

#4

Re: Miter Saw Stands...

Mickey Elam

>I have the Rigid unit and love it. Home Depot should have them in stock and they go on sale occasionally for $99, which is a pretty darn good deal if you ask me! I don't know much about the Delta unit, so I can't intelligently compare them, but I can't imagine that it's much better than the Rigid.

Re: Miter Saw Stands...

#5

Re: Ridgid MSUV

Glenn Madsen near San Francisco

>This was one of the better $100 purchases in power tools and accessories in the last 4 years for me.

I'm not so good at getting the saw AND stand connected and into the back of the pickup. The saw is secured with C clamps, and I take it apart. Easier on the back, with my covered truck.

I haven't used the other rack you mentioned.

Re: Miter Saw Stands...

#6

Re: Miter Saw Stands...

Chicago Bob

>I have used the DeWalt stand for four years now and like it alot. Well built but a bit on the heavy side.

Re: Miter Saw Stands...

#7

Re: Miter Saw Stands...

JackLane

>Hi Rob

I think the Ridgid stand is awesome. I own a cabinet shop and we have one in our 20' utility trailer. I strap it upright to the wall with E-track straps and roll it in and out of the installs every day. I have a DeWalt chop saw on it. One drawback is the weight. If you need to lift it in and out of a pickup, it's a two person job.

I'm also between chop saws in the shop right now too. The old one finally gave up the ghost. I brought this saw and stand into the shop and attached a piece of 3/4" plywood vertically to the fence to prevent tear out. Then I put a piece of plywood 3/4"x 12"x96" across the table and pocket screwed it to the vertical piece I previously mentioned. I used the stand's outriggers to keep the long piece of plywood supported. The first cut through those two pieces makes a zero clearance surface below and behind the cut. Virtually no tear out. It makes a handy semi-permanent chop saw station although there's no fence or measuring device on it.

All the best

Jack

Re: Miter Saw Stands...

#8

Re: Miter Saw Stands...

scottg

>You guys would --buy-- one of those things?? I thought working wood was your thing? hee heh

I made mine from scrap wood of course. Cost nothing but the price of glue and screws. I used the torsion box theory (same as a hollow core door except beefier) and it's plenty strong enough. Weighs about 6 or 7 pounds all in maybe. Legs fold down and a turnbotton keeps them.

I also made a pair of extension stretch out supports but never use them. It too easy to set up some temporary prop on the spot for stuff over 10'.

I can take a picture if you like? Of course, it'll be some kind of tough to access thing since I am not really good with computer graphic tricks.

yours, Scott

Re: Miter Saw Stands...

#9

Re: Miter Saw Stands... *LINK*

Mark Harrison - Brisbane, Australia

>Unfortunately it seems that Delta don't sell the one I own any more (I don't know the model number but see the picture) but it seems that it is still made by some Taiwanese or Chinese manufacturer. The big wheels make this a great tool if you are moving this around a lot.

Don't know where you are going to find these in the US though.


http://www.timbecon.com.au/details/deluxe-power-tool-stand-13451.aspx

Re: Miter Saw Stands...

#10

Re: Miter Saw Stands...

Rob Hix - King George, VA

>Mark,

I came across that one in my research and looked for it. I could not find it available anywhere. It looks as if the one that I am looking at is its replacement.

I am leaning toward the Ridgid product right now. For one reason, several people have said they have it and like it. Also, my saw is a Ridgid and I know it would fit. I am going to run in to Home Depot tomorrow and see if they have any sitting around and if not see if they can order me one. If not I may do with the Delta. I could internet order the Ridgid, but I do not want to pay the $65 shipping charge. If they are not willing to order it for me at the store, then I will go with another brand.

Thanks for the input. It has really helped a whole lot.

Everyone have a safe and productive weekend,

Rob Hix