Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Refinishing

Posts

Refinishing

#1

Refinishing

Ed Freestone

>I'm a beginner woodworker and even more inexperienced at finishing. I need to refinish a dining room table top. It's unspecified hardwood with a heavy satin poly finish that is scratched and chipped. I'd like to remove the poly and refinish with wiping oil/varnish instead. All advice welcome. Thanks.

Re: Refinishing

#2

Re: Refinishing

Lee Schierer - McKean, PA

>I'm not a refinishing expert. The citrus based strippers are less toxic and to my experinece are easier to work with.

Some table are made up of laminated or veneered material. The varnish remover my also remove or loosen the veneer. You will also need to be careful sanding as it is easy to sand through thin veneers.

Varnish removal will also remove some or all of the stain that was applied. You will need to figure out how to match the color for the rest of the table if you are only refinishing the top.

Lee

Re: Refinishing

#3

Re: Refinishing

Clint Searl, at the base of Haycock Mtn

>1. Use a heavy bodied methylene chloride based stripper to get to bare wood.

2. Wash and scrub well with mineral spirits and maroon scotchbrite.

3. When completely dry, scrub to smoothness with a dry maroon pad. Avoid sandpaper; it destroys any patina.

4. Stain, if desired, with a good pigmented oil stain, like ZAR. Let it dry and rub again with the maroon pad.

5. Apply several coats of oil based poly.

6. After a couple weeks, give it a good rub with 0000 steel wool and paste wax, and polish with an old cotton towel.

7. Have fun

Clint

Re: Refinishing

#4

Re: Refinishing

Mark Chaimberg

>Any good quality paint remover will remove the finish for you. If you use a liquid MC-based remover, such as Circa 1850 Furniture Stripper, you will not have to wash the surface after stripping, you will not damage any veneer or glue joints, and will not have to do any sanding.

Unless you plan to use table pads or place mats, I would recommend you use a polyurethane finish as opposed to an oil/varnish wipe on finish for the final coat. Polyurethanes are much more durable, heat resistant and water & alcohol resistant.

Re: Refinishing

#5

And be sure to...

Jim Dillon

>... wear protective gloves and work in a ventilated area if at all possible. Some of the removers are safer to use than others, but the tradeoff is the healthy, nice-smelling ones generally take longer to work. Stripping off finish is a messy, messy job so be sure to work in an area that allows you to clean up afterwards. Good luck.

Jim

Re: Refinishing

#6

Re: And be sure to...

Steve Schoene

>Ventilation is important with MC paint stripper, it's nasty stuff, but much more effective than the others. I would only work out of doors with MC stripper if I didn't have either a serious mask, rated specifically for MC stripper, and/or really serious ventilation (not just a couple of open windows).

Oil/varnish, such as Watco, where you apply it "wet" and after a short time wipe it off, can look nice. They do require periodic "refreshing", and can be damaged. Only choose these if you and your guests are the kind of folks that always use coasters.

I'm going to suggest that you go with a good traditional resin varnish. Polyurethane (single part consumer grade) is OK, but to my mind the traditional resin varnishes are quite a bit easier to rub out to an even sheen. I don't think the extra toughness of polyurethane varnishes is needed for furniture. Behlen Rockhard is good but a bit dark, and for a lighter finish, Pratt & Lambert 38, or McCloskey Heirloom are also good.

"Full strength" varnish applied with a brush, will give a very protective finish after just a few coats--three perhaps, and is easier to "rub out" to eliminate the inevitable dust nibs.

Wiping varnish, either made by thinning a standard varnish such as listed above, or bought that way, such as Waterlox, are somewhat easier to apply, and since they are thinner, dry enough faster that dust is a smaller problem, though not completely eliminated.

I suggest you get some wood that is similar to the table top, and make some practice finishes on it, to see how different finishes work and how they look. Much better to make mistakes on wood that is already scrap.