Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Carving out top of log

Posts

Carving out top of log

#1

Carving out top of log

Brian Altman

>I need to carve out the top of a newly cut tree stump to insert a planter into the top. I want to plant a curly grass in the top of the log in the picture. I thought about drilling a bunch of holes and chiseling it out, a rasp on a drill, a grinder. I know there is a grinder which looks like a chain saw. Don't have it and seems too dangerous to use on a ladder reaching down on the top of the stump.

Ideas???

Thanks

Brian


img

Re: Carving out top of log

#2

I'm Stumped, Brian

George@Colonel's Workshop-Havertown PA

>

Re: Carving out top of log

#3

Re: Carving out top of log

John E. in SC

>Might could use a router with a straight cutting bit to get a nice clean edge at the top, but you wouldn't be able to go very deep w/ this. I suspect a drill / chisel / elbow grease is about the only real way for most of it.

NEAT idea though- I think it will look great, at least for a year or two.

Re: Carving out top of log

#4

Some clarification, pretty please?

Jay Kilpatrick in TX

>Brian,

What is the diameter of the log? How deep do you want it hollowed? How far off the ground is the top of the log?

My first thought was to build up a little scaffolding to get at it with a chainsaw. But that might be over-kill for a small diameter log. If you're only going 3-4", them maybe a powerbore bit, a drill, some stout chisels, a solid mallet, and some elbow grease might do the trick without too much fuss. The router would be helpful up to a point, and might even get 50% or more of the work done depending on the log diameter.

Re: Carving out top of log

#5

Re: Some clarification, pretty please?

Brian Altman

>The log is about 18" in diameter. I am looking to dig out about 6-8" in order to set a flower pot in or just put the dirt in and plant my hair (curly grass).

It is about 10 feet off the ground, but AI can get to one side on a step ladder on the deck.

Brian

Re: Carving out top of log

#6

Re: I'm Stumped, Brian

Brian Altman

>I'm stumped.

Not a good thing for a woodworker, we need all our limbs ;-)

Brian

Re: Carving out top of log

#7

Re: Carving out top of log

Curly Smith

>Do you have the rest of the tree?

How about taking a 2' section from above the "totem", hollowing as much as needed for your planter, drill 2 holes in the bottom and two corresponding holes in your "totem" and attach the planter to the "totem" with two short sections of rebar?

I'd also seal the top to help delay decay.

If you hollow the stump then you'll be stuck with drills, chisels and hard work. Or, maybe you could hire some carpenter ants.

Re: Carving out top of log

#8

Re: Carving out top of log

Rob Stokes in North Vancouver

>I'd cut the top off, hollow it (VERY carefully do plunge cuts with a chainsaw) and stick it back on with a couple of steel dowels (re-bar, reddi-rod, old railroad spikes etc.) and some construction adhesive (5200??).

BUT - before you put the top back on, cover the stump top with a sheet of copper (or plastic) over some wet roofing tar. That will keep the water/bugs away for as long as possible. I'd also carve a drain hole out back and line the inside of the planter with copper (bedded in tar) as well.

Rob

Re: Carving out top of log

#9

Re: Carving out top of log

Mark Mandell - Gone Round In Jersey

>Think the router suggestion will work. Using a strainght bit extended as deep as possible, route the first layer leaving 1" thickness on the outside, then do the next "step" down with the walls acting as a fence. Waht you'll get will look like a quarry. Seal with roofing tar (even better a fiberglass layup) with a drain and you're in business.

m

Re: Carving out top of log

#10

JL

Re: Carving out top of log

JL

>I presume you are talking about something like the Arbortech grinder or the Lancelot or Squire "chainsaw" grinding attachments that fit on an angle grinder. They are fast, but if you are 10' up, they are a bit dangerous. They do work well though.

Another thought - how about a Tungsten Carbide grinding wheel for an angle grinder? You could get a coarse wheel. It would be a bit safer. I've got a medium that I use for chair seats. Wear a face shield and goggles if you do go this route.

Re: Carving out top of log

#11

Re: Carving out top of log

Pete LaBelle

>Plunge to the full depth of a Skil Saw blade into the top, rotate a couple degrees, plunge again. Repeat. This'll make a bowl type hole that will have a bunch of fins that'll need to be chipped out.

Re: Carving out top of log

#12

Re: Carving out top of log

Brian Altman

>Good one. I think this is the best so far. I should be able to get fairly deep.

Thanks

Brian

Re: Carving out top of log

#13

Re: Carving out top of log

Ernie Miller

>How about a Adz and a large out cannel gouge shouldn't take more than a hour or so at the most and will be safer than a power tool. Start at the center and work you way to the outside.

Re: Carving out top of log

#14

Re: Carving out top of log

Rickey LoDico

>Do you have or know anyone with a big lathe? Cut the top off and hollow it out and reattach it.