Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

bandsaw upgrade

Posts

bandsaw upgrade

#1

bandsaw upgrade

ryker acuna

>Got free from my boss an old Rockwell 14" Bandsaw. I have gone through it and its in really good shape. However it has the original 1/2 Hp motor in it. I want to upgrade just to get through my wet turning blanks a little easier. Heres the question should I go to a 1Hp upgrade or if I can get into the 1 1/2 Hp range. I dont know alot about electrical but I thought the higher horsepower would put me in the 230v range, of which I dont have. Any suggestions? I was going to run down to the local industrial surplus and see what I could find.

Re: bandsaw upgrade

#2

Re: bandsaw upgrade

Mark Goodall - ATL - tooljunkie

>A motor using 240V will require half the amps than the same motor on 120V. So since most 120V circutis (in homes at least) are 15A or 20A about the highest motor I've seen at 120V is 1.5HP. Beyond that the amps get too high and would require a circuit like 120V-30A which I've only only seen in industry.

So generally I've found that WW machinery motors:

under 1HP = 120V

1HP - 2HP = 120/240V

3HP and higher = 240V

I have several machines with 1.5HP motors and they run on 120V fine. Just as long as they are the only thing running on that circuit. I can't run my 1.5HP dust collect on the same circuit as my lights or anything else for instance.

If your circuit is 120V-15A I think you'll be fine with a 1.5HP motor. If your circuit is 120V-20A then you will be. Assuming of course you don't have anything else on those circuits.

Congrats on the nice saw. Those old Rockwell's were built to last several lifetimes. You should be able to get a 1.5HP in there with no problems. I've found some great deals on motors at the local salvage yard and surplus stores, and on eBay too.

Happy Woodworking!

Re: bandsaw upgrade

#3

Re: bandsaw upgrade

Barry Irby

>I agree with Mark and:

I have been considering upgrading the motor on my saw. (similar to yours). My father gave me a 2 hp motor, but it has the wrong mounts on it. I would have to have some sort of made or make something myself (money or time). Its a 240 motor. I would have to change the wiring and the switch. The switch really should be double pole single throw (DPST) for 240. The Dad's motor runs at 3450 RPM and the one on the saw turns 1725. It would require new pulleys and belt to keep the saw running at the right speed. The existing belt guard would not fit the new pulleys, I would need to make or buy a new one. I got overwhelmed in the details and have not used the motor because this free motor was too expensive.

There is a moral in this rant somewhere. When you shop for a new motor, be sure the mounting frame matches (type 56?) and the speed is the same (1725). Unless you go to a 2 hp, the switch should be OK, but it might be labeled for it suitable load. Or, try a better blade and keep the motor you have. I did.

Re: bandsaw upgrade

#4

Re: bandsaw upgrade

Jim Swank

>While a motor might be rated at 2 HP and capable of developing it, the actual HP developed and current draw depend on how heavily it is loaded. I'm running my 1.5 HP dust collector and my 1.5 HP lathe on the same 20 amp circuit with no problems. I only run them both while sanding on the lathe (with a drill also plugged into the same circuit. One of these days I'll get time to run a couple more circuits to that part of the basement shop.

Re: bandsaw upgrade

#5

Re: bandsaw upgrade

ryker acuna

>Thanks for the info. I talked to a friend who is an electrician and he said the same thing you guys did. I saw a 1.5 HP motor on Ebay that had everything I was looking for so I might go for it. But Im still going to look at my favorite Industrial Surplus store on the way home from work this week. Im going to order the riser block this week. I put on a new blade and twist belt today. So I think if I get that motor Ill have a pretty nice saw for a couple hundred bucks. Thanks again for all the input, this site has really helped out.

Re: bandsaw upgrade

#6

Re: bandsaw upgrade

Denis Ch�nard, Orl�ans, Ont.

>I have been considering upgrading the motor on my saw. (similar to yours). My father gave me a 2 hp motor, but it has the wrong mounts on it. I would have to have some sort of made or make something myself (money or time). Its a 240 motor. I would have to change the wiring and the switch. The switch really should be double pole single throw (DPST) for 240. The Dad's motor runs at 3450 RPM and the one on the saw turns 1725. It would require new pulleys and belt to keep the saw running at the right speed. The existing belt guard would not fit the new pulleys, I would need to make or buy a new one. I got overwhelmed in the details and have not used the motor because this free motor was too expensive.

Apart from the mount issue and the fact that my motor is 3 HP, this is my exact experience.

Since I had to change at least one pulley, I took advantage of that and chose the pulley size to speed up blade speed to 4000 FPM, and installed a link belt while I was at it. Required a new guard, I made one out of scraps I had in the shop, ugly but effective.

In the end I'm very glad I did the upgrade, it's like I have a new saw.

DC