Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Repair for finish that won't cure?

Posts

Repair for finish that won't cure?

#1

Repair for finish that won't cure?

Ken Platt

>Folks -

I seem to have gotten snared by the problem of some tropical hardwoods preventing a finish curing. I just finished a coffee table top of white oak with ipe breadboard ends. I first finished just the ipe with BLO (to darken it). That seemed to dry ok, so then I finished the whole table top with a wipe on oil/varnish - Minwax Wipe-On Poly. The first 2 coats seemed to be drying ok, but after the third the ipe just stayed tacky. The oak cured normally.

In an attempt to fix this, I have rubbed down the ipe with dry rags and then with rags moistened with mineral spirits. I got off a fair bit of yellowish stuff, presumably uncured finish. I let it sit for a few days, but the ipe still feels sort of soft and tactile, like it still has a not fully cured finish, but it's not tacky. I rubbed again today with a dry rag, and am still getting a bit of yellowish off of it.

So, I'm looking for advice on what to do next. I'd like to avoid resanding, since I think I'd probably be unable to only sand the ipe breadboards, would probably mess up the oak, and then I'd have to redo the whole dang thing.

I'm wondering if a coat of shellac would save me, but I'm wondering if it would stick well, or just flake off by and by. Alternatively, I though of putting on a coat of paste wax and just leaving it at that.

So, who's been down this road and willing to offer their experience or thoughts? This particular project has been one of those in which everything has gone wrong and I just want to get it the heck out of the shop and move on.The table is intended for casual use in out playroom/TV room, will have feet propped on it, have the kids play on it, etc.

Many thanks -

Ken

Re: Repair for finish that won't cure?

#2

My ipe experience

Ellis Walentine, Host

>Although I've never seen it written, or heard it talked about, I'm convinced that ipe is one of those woods that inhibits oil-based finishes drying. I replaced the floor of my back porch/veranda last year and I ran into the same drying trouble with a couple different linseed oil/soya alkyd resin finishes. Here's my take...

First, it will dry eventually. When I mopped my first coat of varnish on the wood, it looked great but would not dry, even though the conditions (temperature, humidity) were favorable. In fact, it wouldn't even tack up. By the time it was dry enough to resist bugs and leaves and stuff, it was already ruined, so I had to scrape it off and start over. The second product I tried was Cabot's Australian Timber Oil, and it dried somewhat faster, but still not quickly, and it remained soft even after it dried.

I suggest you strip the piece back to bare wood, sand it, shellac it with a couple coats of 1# - 2# SealCoat, and then varnish it as usual. By all means use the polyurethane product and not a softer resin.

Ellis

Re: Repair for finish that won't cure?

#3

Re: Repair for finish that won't cure?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Ken,

That is a bummer. I feel about the same as Ellis and think you can limit the stripping and sanding to the breadboards. Mask off the oak. Getting a fresh ipe start is what you need. I had a bummer of a coffee table I did for a client and encountered my first case of silicone contamination. I know that isn't your problem, but mine ruined my disposition. The good thing is that you can fix your problem without compromising the expected good looks of the piece.

George

Re: Repair for finish that won't cure?

#4

Re: Repair for finish that won't cure?

Howard Acheson

>>> 'm wondering if a coat of shellac would save me

Not now but it would have been the thing to do at the very beginning. Ipe is a naturally oily wood which you exacerbated by adding linseed oil. Ipe should be sealed with shellac as the first coat. Then you can coat with the clearcoat of your choice. As said, you will need to remove the finish from the breadboard ends at least. You may be able to do it with a carefuly wielded cabinet scraper.

Re: Repair for finish that won't cure?

#5

Re: Repair for finish that won't cure?

jmohnike

>Follow the instructions for the other postings, I would add one more potential step..wipe down the bare wood with acetone several times allowing time in between for some of the woods excess oils to surface.

You may also try adding anti fisheye to the finish coat. Most automotive parts stores carry it.

Good luck

Joe

Re: Repair for finish that won't cure?

#6

Re: Repair for finish that won't cure?

Ken Platt

>Thanks folks. Guess I should have known there wasn't a quick and easy answer. Fortunately the ipe is just two 3" x 30" strips. Shouldn't take too long, and I think the scraper will be the way to go.

Next time hopefully I'll have the wit to post here FIRST and ask.

Ken