Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Powermatic 66

Posts

Powermatic 66

#1

Powermatic 66

Andre Mallegol

>Hello,

Problems with my PM66. The blade binds when raising and lowering as it gets near the top of its travel. Mostly when raising. I took it apart four months ago, removed the worm and gear segmemt. The arbor assembly swung freely by hand (w/o worm and segment) so I guessed the problem was with the worm or gear segment. Visual examination of worm and segment showed no defects. The worm and segment were reasonable clean, not especially jammed with sawdust. I removed what dust there was, lubed with white lithium grease, reassembled and it worked better but not perfectly. I put the saw into service. It is used daily perhaps one hour per day. Slowly the problem returned, now to the point where something has to be done.

Powermatic has been disappointing in their technical support. The reps don't seem to have hands on experience with the machine. They do not have the same diagrams that came in my manual (machine purchased 2001 new).

Before I tear it apart again I would like to talk to anyone who has had this problem or similiar. Also, I have searched the web for a Powermatic group and haven't found one. Does anyone know of a group?

Any help would be much appreciated. Thanks in advance.

Andre

Re: Powermatic 66

#2

Re: Powermatic 66

Keith Newton

>One thing to watch for might be between the dust shroud and motor, or wiring to the motor getting caught or too short will cause the same symptom.

Re: Powermatic 66

#3

Re: Powermatic 66

Bob Lang

>One of the few complaints I have about our 66 is this issue. The gears in the raising mechanism get gunked up and need to be cleaned periodically. You can reach the gears from below and blast out the gunk with compressed air or a wire brush.

I don't know who came up with the idea of using white lithium grease for woodworking machines, but I'd like to track him down and smack him. It attracts dust and holds it right where you don't want it to be. Squirt WD40 or something similar up there to get rid of the grease/dust goop.

Hope this helps,

Bob Lang

Re: Powermatic 66

#4

Re: Powermatic 66

Andre Mallegol

>Kieth,

Thanks for the response. I've removed the dust shield, no change. I'll check the wiring lead to make sure that's not the problem.

Andre

Re: Powermatic 66

#5

Re: Powermatic 66

Andre Mallegol

>Bob,

Thanks for the suggestion. I can feel the worm gear, seems clean. I'll steal my wife's makeup mirror and take a closer look. I've had the worm out before, should be easy the next time.

The lithium grease suggestion comes from the tech guy at Powermatic.

Andre

Re: Powermatic 66

#6

Re: Powermatic 66

John Lucas

>Andre Check in the articles section. I did an article on how to repair the blade raising locking mechanism on the Powermatic Artisan's saw. I don't think it caused my saw to lock up but it could. My problem was the blade going down during a cut because the lock wouldn't work properly.

Re: Powermatic 66

#7

Re: Powermatic 66

Andre Mallegol

>John,

Thanks for the reply and tip. I'm going to take a look right now,

Andre

Re: Powermatic 66

#8

Re: Powermatic 66

Ben

>If all else fails I would check the fit of the toothed quadrant / segment what ever you want to callit that the worm gear engages. It needs to travel in a very precise arc or binding will occur at some point. I would take the worm gear out and use a dial indicator on the first few teeth and the last few teeth tops. The reading should be really close to each other, I would guess with in .005". If they are not then the teeth are not travelling in an arc and as the blade raises you are trying to bend the shaft supporting the worm gear down and it is binding. there should be a way to adjust the quadrant piece to make it right.

Best of luck.

Ben

Re: Powermatic 66

#9

Re: Powermatic 66

Andre Mallegol

>Ben,

Good suggestion. The last time I had the worm gear out I checked it against a good straightedge. It seemed straight to my eye but with the thread turning it was hard to tell. The teeth looked fine on visual inspection. What's the best way to check that its not bent? Machine shop?

Thanks,

Andre