Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

refinishing

Posts

refinishing

#1

refinishing

Greg Habas

>Although I've done a lot of woodworking/cabinet making, I've never really tried any refinishing. My son & daughter-in-law recently were given a very nice, but old (40 years +) diningroom set. I'd like to refinish it for them, but without all the stripping, sanding etc. The set appears to be mahogany veneer. The surfaces are faded, uneven, with small emounts of scratches. Additionall, I would like to substantially darken the set to match a sideboard that they just purchased (new). I've seen adds for Formby's, but nothing is said about darkening. Can anyone offer some direction??

Thanks

Re: refinishing

#2

Re: refinishing

Clint Searl, at the base of Haycock Mtn

>Refinishing to the extent you suggest must start with stripping to make it worthwhile. Otherwise, you might as well brush it with fence stain.

Clint

Re: refinishing

#3

Do it right

Ellis Walentine, Host

>In this case, since you want to darken the wood, I think the only respectable way to do this job is to strip the old finish, than sand, stain and re-finish. This way, you will gt even stain appearance, plus you will be sanding out all the old scratches and failed finish.

Veneered surfaces can be tricky to strip, depending on how the veneer is glued on, so I think I would try scraping and sanding the veneered parts before you resort to a stripper. And, if you do use a stripper, consider a gentler one, such as some of the products made by Circa 1850 (www.swingpaints.com). Try it on a hidden area first, and when it has done its work, don't use water to scrub off the sludge; use handfuls of shavings or planer chips to rub it off instead.

Ellis Walentine, Host

Re: refinishing

#4

Re: refinishing

George@Colonel's Workshop-Havefrtown PA

>Good Afternoon Gregg,

I have to agree with Clint, having done restoration work semi-professionally for years. You gotta get the present finish off of it in preparation for staining/dyeing/darkening. You may find some firms in your area that do stripping, but be careful and get references. Otherwise, follow Clint's advice.

George

Re: refinishing

#5

Re: refinishing

John Pappas

>Greg, I would like to add a couple thoughts that go against the above comments. I recently refinished some kitchen chairs that are 40 years old. I cleaned and steel wooled the chairs. I made a glaze that I used to blend some worn areas and to cover other blemishes. I then put put a coat of glaze over the entire chair to darken and even the finish even more. Then I finished with several coats of wipe on poly. Now, they do not look new at all, but they look remarkably good. You might consider experimenting with some part of your table to see if a glaze would give you the results you want. If not, then you can strip and redo it according to the above advice. I figure it is worth a try. What can you lose if you are prepared to strip anyway. I might add, that I think glazes are probably not used by most non professional woodworkers and that is a shame. They are a great tool and everybody doing woodworking should at some point learn about them. (I am just learning about them)

Re: refinishing

#6

Glazing

Ellis Walentine, Host

>I agree, John. Glazing is an worthy addition to your finishing arsenal, whether it is for a new project or a refinishing job. It adds character and depth to the piece that you can't get with stains and topcoats alone. Though glazing's overall effect is one of darkening the piece, its primary objective is usually to add character and complexity and the appearance of age. That might be just the ticket here.

Ellis

Re: refinishing

#7

Re: Glazing

Greg Habas

>I'm totally in the dark about glazing. what is it, and how is it done?

Re: refinishing

#8

Re: Glazing

Bill White

>Just an add-on to the glazing thread (developing). I've been using glazes for quite some time. Try to keep raw umber, burnt umber, and a lighter one in the arsenal. I find that those three colors can pretty much do whatever I need.

Just finished staining/glazing the front door to the new home 'cause I did not want the painters to get their hands on it. Fir door, conditioner, wipe-on cherry stain, raw umber glaze to "hang in the corners, then five coats of "Old Masters" water poly. Supposed to last twice the life of spar poly. Really looks good.

Now to wool and wax then install.

Bill

Re: refinishing

#9

Re: Glazing

John Pappas

>Greg, I am haveing computer problems and am in a situation where I can't adequately respond at this time. Basically, glazing is the process of adding color between coats of finish. There are special glazing compounds which are formulated to work easily, but any stain can be used as a glaze. Gell stains are supposed to work well. Put the stain on (again, between coats of finish), and wipe most of it off, just leaving a thin veil of color. I used a mixture of linseed oil, varnish, thinner and artist oil color to make mine. I would suggest you look at books by Bob Flexner, Jeff Jewitt or Michael Dresdner for more information. If I get my computer problem solved soon, I will try to post a better response. Sorry about that.

Re: refinishing

#10

Don't use steel wool!

Jason Roehl in Mulberry, IN

>Never, ever, never, never, never use steel wool with a waterborne poly. When next you have to refinish it, you will rue the day steel wool was invented. Wax is probably not a good idea, either, because with waterborne polys (polies?) you can't go over wax, and there would be no guarantee you got it all off unless you fully stripped the door. With an exterior waterborne poly, you can lightly scuff-sand it every few years and put on another coat or two (thinly, of course).

Jason

Addy protocol: pro painter who has used LOTS of WB poly.