Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Need cabinet door repair help please!! *LINK*

Posts

Need cabinet door repair help please!! *LINK*

#1

Need cabinet door repair help please!! *LINK*

Steve Yakoban

>I'm trying to get a solution to my warped cabinet door problems. The cabinet is about 60 years old and the 59" long door styles are warped. It has been stripped already so I'm trying to get them as straight as possible before being painted. I don't have a router table and making new styles on my table saw is going to be out of reach for me, so I'm looking at ways to reinforce the doors to be as flat as possible.

I started disassembling the doors which are held together with staples only. The original idea (suggested by the stripper) was to use steel reinforcements. I'm wondering now if I can essentially reassemble the door and bond a piece of 3/4" finished plywood panel on the insides.

I don't know if the plywood will be flat enough to begin with or if it will be capable of staying flat over time. Any thoughts on this or other approaches?

Thanks guys


warped door photos

Re: Need cabinet door repair help please!! *LINK*

#2

Re: Need cabinet door repair help please!!

Bob Lemon

>Steve, I've had good luck removing warpage from wooden items by applying heat and pressure on the warped area with a heat gun. Try to get the temperature of the wood somewhere close to 250 degrees. Put the piece down on a flat surface with the bow up and apply clamps to pull it down. After it cools remove the clamps and observe your results. Assuming you still have some warp left, moisten the area, reheat, and clamp, but raise both sides of the warped area slightly off the bench.

If the rails and stiles have a twist to them, clamp them with an edge up so they cantilever over space. Add a bar clamp on the opposite end at right angle. By adding weight to the end of the bar clamp you can counteract the existing twist in the board. By heating the affected area, it will allow the board to rotate in the direction of the added torque.

I've used this method many times to straighten piano keys. Hope it works for you.

Bob

PS This process takes time, so be patient!

Re: Need cabinet door repair help please!! *LINK*

#3

Demo Pics #1

Bob Lemon

>Steve, Here are 2 pictures to show the principle for removing twist. It will take multiple times trial and error to accomplish your goal. Bob


img

Re: Need cabinet door repair help please!! *LINK*

#4

Re: Demo Pics #2 

Bob Lemon

>


img

Re: Need cabinet door repair help please!! *LINK*

#5

Re: Demo Pics #2

Steve Yakoban

>Thanks for the idea. Not being a cabinet maker/repairer I had asked the furniture stripper if there was a way to straighten the styles and they said no, so I figured they know better than me. I'll give it a try, but my one question is: will the "un" warping stay the way I get them, or can they migrate back over time. The cabinet is scheduled to be painted in a few weeks so I won't have long to test the result.

Thanks!

Re: Need cabinet door repair help please!! *LINK*

#6

Re: Need cabinet door repair help please!!

jmohnike

>If you are not concerned with tradition, and just want a flat door,and keep the same look. You can cut a piece of ply 1/2-3/4" thick (the distance between the door and the shelf will determine the thickness), apx 1-2" smaller in all directions. Take the doors apart, remove any tennions from the frame, glue and screw the parts to the plywood, from the back. The old door is now a venieer and each piece is seperate. I know this is a crude method but it does work. If you bevel or route the edge of the plywood it will also help the appearance when the door is open. The only other concern is, if this is top wall mounted cabinet will it support the additional weight, bottom or floor cabinets should not be a problem.

Good luck

Joe