Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Air compressor question

Posts

Air compressor question

#1

Air compressor question

Tim Caley - North Little Rock

>Is there any problem with keeping an air compressor in an un-heated garage? Mine is so loud that I almost hate to use it in the shop. I was thinking about putting it in the garage and plumbing it back to the shop like the article in American Woodworker a couple of months ago.

Re: Air compressor question

#2

No problem with some caution...

John in New Mexico

>My compressor instructions recommend a lighter weight oil for cold weather, range is between 10 weight and 30 weight. Its also got a valve you can open for starting the motor with no load, though most compressors don't seem to have this, you can do the same by opening the tank drain valve. If its really cold, I sometimes point a space heater at it for 10 minutes before starting.

All that said, the telescope site where I last worked has a huge Kellogg American compressor in an un-heated space, with no adaptations or babying, been running that way since the 1960's.

John

Re: Air compressor question

#3

Ab-so-loootlee!

Mark Mandell - Gone Round In Jersey

>I did dat.

But

You gotta put an auto drain on there to keep your tank dry without having to run out to the garage to remember to drain the condensate every other day. Go to McMaster-Carr and put item number 4919K13 in the search box.

May also be available elsewhere.

mm

Re: Air compressor question

#4

Re: No problem

Mark Mandell - Gone Round In Jersey

>John,

Change to "Select" synthetic compressor oil and fagedabowdit.

mm

Re: Air compressor question

#5

Gee, I don't know...

John in New Mexico

>Takes almost a WHOLE quart afterall :):):)

I'll try that next time I change the oil, thanks

John

Re: Air compressor question

#6

I Go

Mark Mandell - Gone Round In Jersey

>2 years on the oil in my I-R 3hp 12cfm compressor. It's never dirty, etc., but as you said, it's only a quart. The Select doesn't carbonize the pump the way petroleum does. IR had to replace my pump, and that's first thing the guy looked for.

Gooo-luck

mm

Re: Air compressor question

#7

Re: I Go

Tim Caley - North Little Rock

>My compressor is oil less, I think that is why it is so loud.

Re: Air compressor question

#8

Re: Air compressor question

Dave Peebles Lyons, Ohio!

>Hi Tim,

I have been running my oiless in the unheated part of my shop for at least seven years with no problems. I moved it out there to avoid the decibels too. It is snuggled up next to my dust collecter. :) Someday I may shell out the $$$ for a nice unit, but for the time being it works really well for blowing the chips out of the hollow forms I do.

Best wishes,

Dave

Re: Air compressor question

#9

Re: Air compressor question

Barry Irby

>I have my 30 something year old Sears (Emerson?) air compressor in an outdoor closet behind my shop. Been there about two years. Oil and All. Did not change the oil. Just put in the shed. Almost never drain the water. Seems to work fine.

Re: Air compressor question

#10

Thanks to everyone that replied!

Tim Caley - North Little Rock

>

Re: Air compressor question

#11

Saves

Mark Mandell - Gone Round In Jersey

>On oil changes. |:-}}}

But not your ears. Important note here. When you place the compressor, plan on using a flexible jumper hose between the unit and the piping. This serves to isolate the noise so it doesn't get amplified in the lines and transmitted to the shop. Also, but sure to use type L copper (1/2" is fine) to run your line "plumbing." You should, however, put a drain leg at the end of the line, and a pressure regulator filter in the basement with give you flexibility in use there as there are times when you won't want/need full pressure. The line drain will take care of any condensation in the line so you're not spraying water mist onto a workpiece or through an air tool's turbine. Attached is a pic of my "air station" in my basement ship. The filter regulator is a HF special at $19.

Hope this helps.

mm


img