Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

All is not lost

Posts

All is not lost

#1

All is not lost

Don Henthorn

>I posted about this yesterday under Weekend Doings but thought I would include a picture of the, well, partially restored planes. These were in the box of tools that suffered from extreme exposure to wetness and Texas heat in the covered bed of my pick up for a month or two. I thought they were ruined forever. However, with time on my hands I decided to give them a chance and with a wire wheel and sandpaper I managed to get them back into usable shape. The blades, surprisingly, had very little pitting in the cutting areas and I was able to get a good edge on all of them. The number five and the number three are in pretty darn good shape for what they went through. The little block plane is the only one I kept out of the half dozen I had, and it came out pretty good as well. I bought it years ago at a flea market and when I bought it there was a brass patch on the sole, but it is as smooth as glass and has never affected the plane's use. I have used it a couple of times since the recovery and it seems as good as ever. The old Sears monstrosity I kept just for old times sake. I never really used it that often, but when I did need it I was glad to have it. I am missing a thumb knob for it.

Here is a picture of the number three showing thwir general condition before I worked on them. Then the picture of them as they are now. There is still some residual rust where I couldn't get at it with large wire wheel. I will get a smaller cup wheel to get at the more difficult regions at a later time, I hope.







Re: All is not lost

#2

Re: All is not lost

nailshooter

>Truly a labor of love. Nicely done.

Robert

Re: All is not lost

#3

Keepers

George@Colonel's Workshop-Havertown PA

>Good Afternoon Don,

I am glad you took the time to resurrect those planes when you did. A couple more months, and the rust would have been worse and deeper. It seems I favor the planes which I have brought back from the rust bucket, or otherwise rescued. I wish I had a pix to share of my #6 before and after. Judging by the pix, you spent a few hours of toil bringing these back into shape. Hope you enjoy them a long long time. Tools are best when used.

George

Re: All is not lost

#4

Re: All is not lost

Fred West in West Chester, PA

>Don, as mentioned before truly a labor of love and a beautiful job. Love seeing older tools resurrected. Great job and I would love to see them when you get them finished with the smaller wheel. Fred

Re: All is not lost

#5

The best rust remover Re: All is not lost

del schisler

>these were made by boeing aircraft company I use these and find them to be the best i have found not much work to get the rust off just spray with rust free and let set wip than with some steel wool get the rest off than use T9 spray it will not rust again Their are instructions

http://www.theruststore.com/Rust-Preventers-C4.aspx?UserID=636665&SessionID=HaSu43sVxPoov9wd2K8B

and this one also

http://www.theruststore.com/Rust-Removers-C1.aspx

Re: All is not lost

#6

Re: Nice job Don.

Larry Clinton At Frankfort (Central)., Indiana

>I like to see old tools saved and used again. I did play with the electrolysis method of removing rust on some planes and other tools I purchased at yard sales and auctions. It does work well and is almost no labor. I'm sure you are familiar with the technique. I also purchased some "Pure Wax" -liquid floor wax. I have used this on some of the planes I resurrected and it seems to prevent any rust for a long time. I have an old surface grinder and have ground the bottom and sides of 3 or 4 planes then used the wax. Without the protection the freshly ground surfaces start rusting in a day. With the wax I haven't seen any staining in over a year. It may not be orthodox but works well for me.