Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

"New" pen turner questions

Posts

"New" pen turner questions

#1

"New" pen turner questions

Terry Alexander

>I inherited a lathe from my FIL.....Never owned or used one before, so I took a pen turning class just to learn the basics. What a blast!

So...I think I will try my hand at some of these...which brings me to....

I have a farm in West Texas and I have lots of mesquite trees there. Not big enough for furniture projects, but certainly I can see acres and acres of pens out there.

The trees are in 2 distinct conditions. I have living trees and I have some that have been dead for years.

Questions are:

Can I cut up the dead ones and make pen blanks out of them?

Can I cut up the living ones and use them immediately....or do I need to let some time pass for them to dry out.

Thanks in advance.....boy....I can't believe how many pen blanks I have thrown away over the years ;-)

Terry Alexander

Re: "New" pen turner questions

#2

Re: "New" pen turner questions

Curly Smith

>You might want to repost your question on the Turning Messageboard.

But to answer your questions -

Can I cut up the dead ones and make pen blanks out of them?

Sure, as long as the wood isn't rotten. However, even "dead" wood needs to stabilize. A moisture meter might be of some use but you'd probably be better off weighing the blanks.

Can I cut up the living ones and use them immediately....or do I need to let some time pass for them to dry out?

You need to let the wood dry and stabilize. General rule of thumb for air drying is 1 year per inch of thickness. Thinner wood tends to warp more than thicker wood so you might need to experiment a bit to find what works best for your conditions. You can find plans on the internet for solar kilns, your pen blanks might be a good project for such a kiln.

I'd start by cutting some dead and still living wood into blanks roughly 2x the size I wanted. I'd then weigh them on a regular basis and when the weight stabilized I'd cut them to the final dimensions and, again, set them aside to stabilize. With a bit of record keeping you should be able to determine the proper rough pen blank size that minimizes drying time while maximizing the number of turn-able blanks.

Lastly, you could probably sell some pen blanks on Ebay once you've mastered the art of cutting and drying them.

Of course there isn't any reason why you can't still practice turning some pens while you're waiting...

Re: "New" pen turner questions

#3

Re: "New" pen turner questions *LINK*

Ron in Drums PA

>You need to let the wood from the live trees dry.

I cut green blanks 7/8" to 1" square and 6" long. Then I build a "Lincoln Log" fort out of the blanks and let them dry. Here in Pennsylvania it takes about 2-3 months to dry in the winter, (I place them near my oil burner) a little longer in the summer. I lose maybe 2-3% of the blanks from cracking.

If I was in a rush, I'd dump the green blanks in a tub of DNA, close the lid and let them soak overnight. The next day I would toss them in a brown paper bag. Most times they would dry in about a week or so.


Turning Forum

Re: "New" pen turner questions

#4

Re: Mesquite turning

Al Stokka - Cambridge, Iowa

>When you arrive at the time to turn a pen, remember that mesquite doesn't like pressure. Tighten the nut on the mandrel only enough to hold the blanks and no more. Overtightening will cause a blowout...but not until you pen is nearly completed...and you've wasted your time and a couple of brass tubes.

Dead mesquite: I would cut a few blanks, drill a hole (no brass tube for this test), mount two on a mandrel (not too tight, remember?), turn them a down, and let them sit in the house for a couple weeks. If they react (warp, split, etc.) you'll know they aren't ready yet. Using this method avoids wasting the brass tubes. What about wasting the wood? Ha! Doesn't sound like you need to worry about running out. ;^)

Live mesquite: I would slice lumber about 1" thick, stack the lumber with gap between the boards in each layer and spacers between each layer and let it dry. I leave it for a year. Then cut it into blanks of whatever size you require.

Al