Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

OT - Metal Frame Pools

Posts

OT - Metal Frame Pools

#1

OT - Metal Frame Pools

John in MD

>Thanks in advance for any replies, and apologies for the OT posting...

The kids have outgrown the plastic wading pools, and our current financial state don't allow the purchase of a real above-ground pool. We've heard some scary things about the soft-sided, bulbous-looking "easy-set" pools, but the same company makes similar pools with straight sides, held up by metal pole framework.

We're wondering if anyone has personal experience with these sorts of pools. They look like an OK deal (keeping in mind they're sort of a bridge between the plastic wading pool and a "real" pool). Sizes should be good for the kids at their ages, and rough-housing isn't an issue, so durability really would relate to how many years of use we could expect to get from one of these things.

Also, any tips or tricks about installation - seems straightforward, but I wonder how flat an area it needs to be on (How flat is flat??), and ideas for surface prep (dig out turf grass? lay groundcloth and cover with sand? lay sheets of fiberglass insulation material for a flat bed?). The instructions are pretty vague on this, and sounds like you just spread the liner over your existing lawn, build the frame, and fill it with water...

Maintenance issues? Overwinter storage hints??

Any replies will be appreciated - either on the board or direct to my email.

Many thanks.

-John-

Re: OT - Metal Frame Pools

#2

Re: OT - Metal Frame Pools

Dan Donaldson

>I use one of these, mainly because my wife likes to play in the water and I don't want the expense of a "real" pool. The one that I have is 18' round and is about 3 1/2 feet deep. The main issue with these is that they don't have a skimmer, which makes it very difficult to keep them clean. I went to a pool place and bought a skimmer for an above ground pool (around $20 or so) and cut it into the side of the pool, blocking off the old connection. This helps immensely. The other issue is that the pump/filter is a small one with a cartridge. I bought a regular above ground sand filter pump and hooked that up. With these mods, it works fine. I get about 3 years out of one. I am on the second one now, and am using the same pump/filter I got for the first one.

In the winter, I drain the pump and filter and lower the water in the pool below the intake/exhaust (to keep the shape), cover it, and wait for spring. In the spring, I empty it, clean it up, and refill. If I keep track of the chemicals and run the filter, it is good to go for the year. This is one that "real" pool users may scoff at, but it works for me, and my wife loves it.

Re: OT - Metal Frame Pools

#3

Re: OT - Metal Frame Pools

Pete Stahl

>John,

When I moved into my last house it came with 24 ft dia. pool as is. The filter didn't work so I bought a DE type filter for. Water stayed really clear but we'd get algae around the bottom edge because the kids wouldn't swim in it enough to keep the water moving. They'll nickel and dime you but not like a in ground pool. I took the pool down after aprox. 8 years because the liner finally went bad. Nice thing about above ground pools is after they're gone, a little top soil and some seed and you never knew it was there. Go with as big as you can afford. Sand or DE filter is a matter of preference, they both do a good job. It's keeping the chemicals right that's the tuff part.

Re: OT - Metal Frame Pools

#4

Re: OT - Metal Frame Pools

Curly Smith

>The only things I would add to the following have largely been covered. Check with your local pool supply company about a bigger filter package and make sure that you have a skimmer.



Above Ground Swimming Pool Basic Installation Guide

As the guide mentions, don't overlook site drainage. You're putting in a very large obstruction and you don't want to cause yourself additional problems.

FYI - I don't have a pool anymore but these sound interesting:

Solar Powered Pool Purifier and one might alleviate a good bit of the maintenance work. They're a bit pricey at $270, plus the associated refills every 1-2 years $50.

Re: OT - Metal Frame Pools

#5

Re: OT - Metal Frame Pools

Larry Clinton At Frankfort (Central)., Indiana

>I have helped install a new liner one time on a large above ground pool. We did quite a bit of prep work on the base where the liner sat as the guys I worked with had some bad experiences with the liners tearing where they rested on irregular ground. We hauled in enough sand to cover the base a couple inches deep, wet it and rolled it with a lawn roller prior to installing the liner. The liner really looked good when we were done with a perfectly smooth bottom - no wrinkles. We also adjusted the sides using clothespins as the pool filled. We cut and sealed the openings for the filters when the water was just below them. After it was about 2/3 full we trimmed and permanently attached the top. This seemed to work very well and the liner was very smooth with no stresses or wrinkles. This was my only experience.

Re: OT - Metal Frame Pools

#6

Re: OT - Metal Frame Pools

Charles Sharp

>My neighbors had these when I was a kid and we had one for my kids. Putting the sand in the bottom under the liner will extend the life of the liner. If you don't use sand, make sure there are no roots or rocks under the liner or you will get leaks.

Also, an elevated deck on one side of the pool that is level with the top of the pool is a really nice addition.

Last, but very very important - BE SAFE

Re: OT - Metal Frame Pools

#7

About the sand.....

Jason Roehl in Mulberry, IN

>...my friend has an above-ground pool, and when they put it in, they were told to use Mason's sand. It's cleaner, finer, and will compact, allowing the liner to last longer and stay put.

Jason

Re: OT - Metal Frame Pools

#8

Re: About the sand.....

Larry Clinton At Frankfort (Central)., Indiana

>Didn't know there was a difference in the sands Jason. The sand we used was probably "masons sand" as we hauled it from Frankfort Masonry supply

(now IMI concrete). I was raised in sand country - Northern Indiana - only differences we saw was the normal coarse sand (like the dunes) and the fine -kinda of rounded grain sand in some of the swamps - quicksand.

Re: OT - Metal Frame Pools

#9

Re: About the sand.....

Jason Roehl in Mulberry, IN

>I didn't either, Larry, until my friend put up that pool. I think the idea is that the mason's sand won't move around under the liner as you walk on the bottom of the pool.

Jason

Re: OT - Metal Frame Pools

#10

Swimming pool chemistry

Bob Fawcett

>I use the advice here to keep my pool crystal clear, and it is a lot cheaper than pool store chemicals.

www.poolsolutions.com

Check out the BBB system.

Re: OT - Metal Frame Pools

#11

Thanks for the replies

John in MD

>Much useful information, and I appreciate everyone's time in replying.

Seems like smost of the responses were about regular above-ground pools, though, and I was asking about the wal-mart version - just a liner held up by metal pipes (Sand n Sun is the brand name)...

Hope to get a "real" above-ground pool someday, but for now this will have to do.

Thanks again.

-John-


img

Re: OT - Metal Frame Pools

#12

Re: Thanks for the replies

Dan Donaldson

>That is basically what I have. Looks just like that except for the addition of the skimmer.

Re: OT - Metal Frame Pools

#13

Thanks, Dan -

John in MD

>The skimmer sounds like a great idea, and I'll look into doint the modification. I was mostly concerned about just spreading the thing out on the lawn - whether this would be flat enough or if I needed some sand or something underneath.

Thnaks for your replies.

-John-

Re: OT - Metal Frame Pools

#14

Up north.....

Mark Goodall - ATL - tooljunkie

>Up north I'm seeing that above ground pool installers are installing on 1" thick styrofoam board instead of sand. Interesting.

I don't think they'd do it down here....... termite food.

Happy Woodworking!