Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

finishing salvaged heart pine

Posts

finishing salvaged heart pine

#1

finishing salvaged heart pine

matt berry, richardson, tx

>I recently obtained about 100BF of salvaged heart pine floor decking from a turn of the century cotton mill in North Carolina. I am using it to create two bartops in my kitchen. The lumber is plain sawn, but is almost 3" thick, so I am quatersawing each board and glueing them up to form about 18" deep tops. I have small children, so I know these tops will take some abuse, and I want something that will bring out the beautiful patina and quatersawn figure. I was thinking of using a blend of linseed, tung, and polyurethane, but having never used a product like that, I am not sure if that is something that can be maintained like and oil and wax combo could be.

I think pure poly is probably not the way to go since when I inevitably need to repair scuffs and scratches, it will be more involved. Plus it won't highlight the grain like I want. Then again, I'm no pro at this, so I may be completely wrong. The tops will not be used for cooking or meal prep, so water would only come from cups sitting on them, and there will be no cutting on them. Any recommendations would be greatly appreciated.

Thanks,

Matt

Re: finishing salvaged heart pine

#2

Re: finishing salvaged heart pine

David Yoho

>One product comes to mind, given what you said. You're right that polyurethane could not be repaired once cured. I think something that protects as well but probably doesn't dry as hard as poly is Waterlox Original. It's tung oil based varnish that's easy to apply and looks great. However, if there is a need to apply more down the road, unlike poly, Waterlox will adhere to itself later.

David

Re: finishing salvaged heart pine

#3

Re: finishing salvaged heart pine

Stephen Shepherd in the State of Deseret

>I would avoid any hard plastic finish that can delaminatem, chip off and impossible to repair.

If it is going to be around food preparation I would suggest walnut oil, it is edible and actually dries and protects the wood. Apply a good coat, wipe of any excess and allowing to dry at least 24 hours before repeating the process. Renew it as needed and with a good balsamic vinegar makes a delightful salad dressing.

Stephen

Re: finishing salvaged heart pine

#4

Re: finishing salvaged heart pine

robert davis

>ihave minwax wipe on poly on a pecan counter top.. 4 coats 5 years ago.. couple coat renewal twice since..{satin}

Re: finishing salvaged heart pine

#5

Re: finishing salvaged heart pine

Mike Fitterling

>Shellac is a great finish for heart pine. It really brings out the beauty of the wood. I like orange, but garnet would probably look good, too. You will still need to topcoat it with something more durable, so make sure to use dewaxed shellac for that. I would probably go with poly for the topcoat in this situation. I used poly on our fireplace mantle and it looks good, should look even better with some shellac under it.

Re: finishing salvaged heart pine

#6

Re: finishing salvaged heart pine

Michael Wilkins

>I have used Garnet shellac on heart pine before with great results. This will not mask the natural color of the pine and is a real easy finish to renew. If you want more water protection, follow the shellac with a wipe-on finish like Waterlox.

Couple of years ago I visited the site of an old cotton mill being dismantled in Cliffside, NC where my dad and granddad grew up. There was enough lumber there to cover the equilavent of 2 football fields while I was there, and more being removed. Probably going end up on someones' floor. Nice to see it being reused instead of in a landfill.

Re: finishing salvaged heart pine

#7

Behr clear water borne one-part acrylic epoxy

Clint Searl, at the base of Haycock Mtn

>

Re: finishing salvaged heart pine

#8

Re: finishing salvaged heart pine

matt berry

>i agree, and it's fun to work with too. and even though i tried for hours to get every single bit of metal, wouldn't you know i still knicked up my planer and jointer blades. planer's are reversible, so no big deal, but it's worth it anyway. i'm not the most environmentally conscious guy in the world, but the wood is so beautiful, it makes sense to recycle it. (cheap too, only $2.50 per BF!)

thanks for all the great advice.

matt