Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Lady Morris

Posts

Lady Morris

#1

Lady Morris

Mark Mandell - Gone Round In Jersey

>It's taken more time and "discussion" than I care to remember to get a decision made on fabric, but my spindle Lady's Morris chair, with "ankle stool" is finally done. Cherry, finished in Watco, then sealed with dewaxed garnet shellac, and topcoated with Target Ultra acrylic lacquer.

Comments welcome

MM


img

Re: Lady Morris

#2

Re: Lady Morris-Detail 

Mark Mandell - Gone Round In Jersey

>


img

Re: Lady Morris

#3

Re: Lady Morris

Larry Clinton At Frankfort (Central)., Indiana

>Very nice looking chair Mark, looks real comfortable. I'd like to see a closeup of the through tenon on the leg - I'm doing some through tenons on a blanket chest - yours look great.

Re: Lady Morris

#4

Re: Tenons

Mark Mandell - Gone Round In Jersey

>Get this close and every dust mote shows |;-}}

Mortices were cut with a JET bench-top from the back to about 3/16" from the front surface. I then finished them by cutting back in from the front side with a 1/4" chisel to prevent tearout. Tenons are done with a sled on the router table with a planer bit, then champfered to fit.


img

Re: Lady Morris

#5

Re: Lady Morris-Detail

Ron in Drums PA

>Nice chair Mark, how'd you do that on your lathe?

Re: Lady Morris

#6

Re: Lady Morris-Detail

Mark Mandell - Gone Round In Jersey

>Ron,

You HAVE heard of offset and segmented turning, right?

Well now you've seen off-lathe segmented turning! "Turning" tree trunks into lumber and then "turning" the lumber into a chair, all without ever touching the lathe or the lathe tools.

Yes, I know it sounds like some magic act based on smoke and mirrors, and I did, indeed, have my doubts it could be done, but in the end I think it turned out reasonably well considering the complete lack of roundness.

|;-}}}

mm

Re: Lady Morris

#7

Re: Lady Morris-Detail

Ron in Drums PA

>I get it - you started round then went to flat! Interesting concept!

Re: Lady Morris

#8

Lotsa Work, Mark

George@Colonel's Workshop-Havertown PA

>Good Evening Mark,

I'd have to find somewhere to sit after that much effort. I suppose your first choice was already occupied. Nice job. Now its time to make a big brother.

George

Re: Lady Morris

#9

Big Brother

Mark Mandell - Gone Round In Jersey

>Was purchased from Stickley, in leather. Besides, with the hassle over fabric etc., I'm more than likely to say "go buy it" when the piece is to be upholstered. Funny though, the little one, with the big cushion and adjusting back is the very comfortable. Have to make a side table to serve it.

Thanks.

mm

Re: Lady Morris

#10

Yeah

Mark Mandell - Gone Round In Jersey

>he he.

That's the ticket. Does feel really weird, though.

mm

Re: Lady Morris

#11

Re: Tenons - Thanks Mark!

Larry Clinton At Frankfort (Central)., Indiana

>Nice job! I just finished cutting 48 tenons on the TS - wondered at the time if the router might work better. I think I will build a sled and try it before the next project.

Re: Lady Morris

#12

Re: Sleds

Mark Mandell - Gone Round In Jersey

>I use the sled design shown in Bill Hylton's Router Magic. Works well and very accurate. Have one set at 90, another at a fixed 45, and the third is adjustable. Never much liked the table saw thingamajigs.

mm

Re: Lady Morris

#13

Re: Big Brother

George@Colonel's Workshop-Havertown PA

>Yes Mark,

For a long time most of my work was upholstery, and I've given it up nearly completely now. It can be a PITA. When I did it, all vibrant exclamations from others were tempered by my thought: Thank God that's over".

George

Re: Lady Morris

#14

Re: Lady Morris

Mike Rubes, Apex, NC

>Hi Mark,

Very nice!! I like the fabric so think the time was well spent in the decision making process. Always fun to see what other turners do for flatwork. That looks like a nice cozy spot, get you a small floor lamp and that would be a great reading spot with the window.

Thanks for the pictures,

Mike

Table saw has become a temporary work table in Apex, NC...

Re: Lady Morris

#15

Re: Lady Morris Thanks

Mark Mandell - Gone Round In Jersey

>Mike,

Working on a Prairie-inspired serving table to hold the book and port glass. |;-}}}

Comfy, indeed. 'Specially when the sun comes in through the trees. Can't wait for the kid to get her Total Gym out. Doesn't much match the mood.

Thanks to all for the comments.

mm

Re: Lady Morris

#16

Re: Lady Morris

Jim Shaver - Oakville, Ontario

>Very nicely done Mark,

I love the chair, the ankle stool is priceless!

Take care,

Jim

Re: Lady Morris

#17

Re: Ankle

Mark Mandell - Gone Round In Jersey

>I actually had to research the ankle stool thing. Turns out it was proportioned to allow the "Lady of The House" to raise her feet and recline, but still avoid an "unseemly show of ankle in genteel company."

he he |;-}

mm