Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Questions on "truing up" a table under contruction

Posts

Questions on "truing up" a table under contruction

#1

Questions on "truing up" a table under contruction

Barry Irby

>I have been making a 42 by 70" table and posting questions and you guys have been very helpful, as usual. I built it with M & T joints from the rails to the legs. Careful to cut every thing square and true. Assembled the table frame with a single bar clamp on each side to pull the tenons tight into the mortises. The shoulders came up nice and tight and looked good. The diagonals at the tops of the posts were off by a 1/32", so I left them alone. The lengths of the sides and ends were as accurate as I could measure. The table frame sat flat on the floor (As if the floor were level, let's hope, it a slab) The legs are 3 3/4 square at the top with a turned section.

Now for the questions: I turned the table upside down to prepare for the top and happened to pull a tape on the bottoms of the legs. The lengths and widths are off maybe 5/16" and so are the diagonals. Is this "normal". The error is not visible and I can't see how it will ever affect the function of the table, but my curiosity is up. Does anyone else ever try to square and true both the top and bottoms of the legs? Has anyone else even checked?

Re: Questions on "truing up" a table under contruction

#2

Ellis Walentine

Sounds normal

Ellis Walentine

>You can probably use a framing square to see which leg is out of kilter. Those shoulders that looked tight might not be quite as tight as you thought, or they could be off by a tad, which would translate into the 5/16" you're seeing. If so, you can compensate for it by shifting one of your clamp pads a little bit when you glue it up. Unless you can see the discrepancy with the naked eye, or unless it makes the table sit cockeyed on the floor, I wouldn't worry about it.

Ellis

Re: Questions on "truing up" a table under contruction

#3

Re: Questions on "truing up" a table under contruc

Ted Wong

>It doesn't take a lot of deviation at the M&T joint to end up with a leg out of square at the bottom. I usually take a swipe with a plane on the mortise side of the joint until I get the leg to tilt back the way I want it to go.

Re: Questions on "truing up" a table under contruction

#4

Re: Questions on "truing up" a table under contruc

George@Colonel's Workshop-Havertown PA

>Good Morning Barry,

If it ain't broke, don't fix it. A table that size will have a little misalignment. What you have is eminently "live-with-able" and shouldn't detract in any way from the table's good looks or utility.

George

Re: Questions on "truing up" a table under contruction

#5

Thanks, Ellis, Ted, and George

Barry Irby

>Like many other things I don't have, I need an assembly table with a perfectly flat top big enough to accommodate any project along with a bigger shop to put it in. If I had one I could have assemble the table upside down and been able to check both the top and bottom for level and square and true.

Actually I am very pleased the frame came out as well as it did. What little bit it is out fo true is not noticeable and does not matter at all. I suspect Ellis is right. Had I known or measured, I could have adjusted the clamps and pulled it in a little better, but I did not and don�t really care.

I am somewhat dysgraphic and am really pleased all the legs are pointed in the right direction. Would not have been surprised to come in the next day after the glue really set and find one or even two pointed straight up.

Ted, a plane is yet another thing I don't own. At least not one that would trim the shoulder on a tenon. I'm not really feeling irresistibly drawn to the quiet side. I do go over to the round side once in a while and I can't afford another obsession.

Ellis, Thanks for the advice on the tenons. I had cut the mortises with a 3/8" bit and on your advice I went back and enlarged them to 1/2" and made them deeper. I also laminated a piece about 5/8" thick down the inside of the 3/4" rails. The frame is rock solid.

And George, you are right. This table is a gift and if they are not willing to live with it, I will take it back.