Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

12" miter saw won't cut square?

Posts

12" miter saw won't cut square?

#1

12" miter saw won't cut square?

John Meikrantz

>I am having fits trying to get my Bosch 12" miter saw (3212) adjusted. When I adjust the fence to square it to the blade, the actual cut is not square. I can adjust the fence to be "out of square" with the blade and get pretty close to a square cut, but I'm sure that isn't the best way to do things. Using an 80 tooth, full kerf, thick plate blade. Am I missing something here?

Thanks,

JohnM

Re: 12" miter saw won't cut square?

#2

Re: 12" miter saw won't cut square?

Dwight Hohweiler

>adjust the index marker

Re: 12" miter saw won't cut square?

#3

Re: 12" miter saw won't cut square?

John Meikrantz

>That's kind of a pain, because of the spring loaded zero detent. Don't think I can adjust that at all.

John

Re: 12" miter saw won't cut square?

#4

Re: 12" miter saw won't cut square?

John in New Mexico

>On some saws you can loosen the fence from the top and adjust it relative to the blade. I've also seen dull blades vibrate a lot, often harmonically or in "pulses" while cutting, but that would look more like a rough cut than an out of square condition.

John

Re: 12" miter saw won't cut square?

#5

Bart Goldberg

Call their Customer Support

Bart Goldberg

>

Re: 12" miter saw won't cut square?

#6

Re: 12" miter saw won't cut square?

Curly Smith

>Check the fence:

- is it square all across the table?

- is it flat across the top, bottom, middle?

Re: 12" miter saw won't cut square?

#7

Re: 12" miter saw won't cut square?

John Meikrantz

>The blade is new and sharp. The fence is flat from left to right, as measured with a straightedge, and it is 90 degrees to the table. After more experimenting this morning, it appears that the head is able to move side to side slightly, due to a very small amount of play in the rear vertical pivot/spring. Not sure if I can do anything about that. Any ideas?

John

Re: 12" miter saw won't cut square?

#8

Re: 12" miter saw won't cut square?

Curly Smith

>Is the "out of square" cut you're getting repeatable? In other words, if you cut two pieces are they both off the same way? If so, I would doubt that the problem lies with the play in the pivot as you would have to have identical error in both cases.

Have you checked the blade to ensure that it's flat and that it runs true?

Is the cut "out of square" top-to-bottom or front-to-back (or both)?

Re: 12" miter saw won't cut square?

#9

Re: 12" miter saw won't cut square?

John Meikrantz

>Blade is flat, runs true. The error in the cut is from front to back, and it is repeatable. Appears to be about the same offset on every cut. If I put light outward (to the right) pressure on the handle as I cut, it cuts pretty close. Seems to indicate that while cutting, the blade shifts to the left.

Thanks,

John

Re: 12" miter saw won't cut square?

#10

Re: 12" miter saw won't cut square?

Larry Clinton At Frankfort (Central)., Indiana

>John, I'm not familiar with your saw, but my Dewalt has slots in the Curved indicator plate with the detents. In other words, if I loosen the screws holding the indicator plate, the saw itself (even locked in the detent) will move left to right. This is an adjustment to "square" the cut. I adjusted mine a couple times - I have moved it to my sons house several times to cut trim & knocked it out a few thousands. After adjustment it is dead on. May want to look at your owners manual, I would think all this type saw would have some adjustment to "0" it square.

Re: 12" miter saw won't cut square?

#11

Re: 12" miter saw won't cut square?

Curly Smith

>I agree with Larry. You've made all of the other adjustments and verified everything else is OK, so all that's left is adjusting the miter scale so 0 is actually 0 (instead of the 0.05 like it is now). Hopefully, your manual will tell you how to make the tweak.

How about a little trig to find out how far off it actually is? You know you want to...

Re: 12" miter saw won't cut square?

#12

Re: 12" miter saw won't cut square?

Dave Bair, Eaton Rapids, MI

>I have a Skil, which is a clone of your Bosch, without some of the extras. Unless I'm cutting with the full width of the blade in the wood, I often get an out-of-square cut. So, if I'm sneaking up on a cut by taking small "shaving" passes, I need to lower the blade very slowly; it takes longer to shave off 1/32" than to cross-cut an 8" board. You can pivot the whole fence to get the 90� indent to engage at 90�. I also let the blade run for a few seconds before I lower it into the wood.