Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Air compressor trouble

Posts

Air compressor trouble

#1

Air compressor trouble

Denis Ch�nard, Orl�ans, Ont.

>I was in the garage tonight, using an air grinder (the type used apparently in muffler shops, looks like a die grinder, but has a shroud, and uses 3" disks). Ran it a bit hard, i.e. did not let the compressor cycle in and out at times, but then not for that long. I had noticed in the past that when the compressor cycled out I could hear a hissing sound that seemed to come from the pressure switch area, and would last something like 10 seconds or so.

In any case, as I was using the grinder, at some point the compressor stopped kind of unexpectedly. I then heard a "pshttt pshttt pshttt" sound that came from the crankase dipstick vent hole, that lasted maybe 20 seconds. The motor was warm enough that I would not leave my hand on it, but it wasn't that bad...

At first I tought that the "compressor engine" seized, tripping the fuses, but with the power off I could turn the pulley at the motor without much effort. I then guessed that the motor overheated, so I let it rest for an hour or so, pressed the thermal protection button, and tried to restart it. No go. I had checked the fuses before that, and I still get continuity when tested with an ohmmeter.

So it seems that the pressure switch is the culprit, but how can I know for sure? The compressor is a Campbell-Hausfeld, 60 gallon vertical tank, "7 HP" (yeah right), draws 17.5 amps on 220, 15.6/13.7 CFM at 40/90 PSI, cut-in at 110 PSI and cut-off at 135. When it stopped it had not reached 135 PSI, it was about at 125. The compressor is about 8 years old, and has not seen much use. Oil level in the crankcase is OK.

Am I on the right track, or am I missing something?

TIA,

DC

Re: Air compressor trouble

#2

Uh oh... Doesn't look good...

Denis Ch�nard, Orl�ans, Ont.

>Just opened the pressure switch. Everything looks normal. I get power from the line, and the contacts work (I get continuity between the line and motor lead on both legs, as it stands the switch is on). However I get no continuity between the two motor leads, should I not get one?

If my understanding is correct, either the motor is toast, or the thermal protection switch is (the motor is cooled down now).

Any ideas?

TIA again,

DC

Re: Air compressor trouble

#3

Re: Air compressor trouble

Keith Newton

>The sound of air leaking when it turns off is to drain or release any pressure in the pump cylinders, so when it starts up again, it won't be starting under a lot of compression. There is a check valve where the line enters the tank. These two things let the motor start without being under a load.

I am not so sure that you have a problem yet. If the motor quit from overheating, but the switch was in a range where it would normally be satisfied, it may not come on until the pressure drops below the start point if the power was disrupted while running, even if it didn't make it all of the way to the shut off point.

I suggest that you drain off some air, and get below the start pressure, and make sure that it doesn't run.

Re: Air compressor trouble

#4

Re: Air compressor trouble

Denis Ch�nard, Orl�ans, Ont.

>I am at below cut-in as it stands (less than 100 PSI), the pressure switch is on. The hissing sound used to run for 2-3 seconds when the compressor was new, now it can go for like 15-20 seconds, which doesn't sound normal. What worries me is that the compressor stopped before reaching the pressure cut-off point. If the motor overheated (which I doubt), either it is toast, or the thermal protection switch is shot. Don't want to sound pessimistic, but for now the shot motor seems like the most plausible possibility. But there was no burning smell I could detect, which is odd if the motor burnt up...

DC

Re: Air compressor trouble

#5

Just thought of another possibility

Denis Ch�nard, Orl�ans, Ont.

>Just went in the garage for some "fresh air" (I don't smoke in the house), and looking at the compressor a light went on... Something I didn't mention, the motor is capacitor start/capacitor run... My DC conked out on me last year, and the culprit was the run capacitor... Too late to check it now, I'll take a look at that tomorrow...

DC

Re: Air compressor trouble

#6

Re: Just thought of another possibility

john lucas

>Dennis If you can short across leads that go to the thermal switch that will eliminate that as the cause. Some switches are built into the motor so you can't do that.

If it's the capacitor you should be able to start the motor by spinning it yourself. At least that's what I've done when mine died.

If your reading continuity across the pressure switch then I don't think that is the problem. If you want to find out for sure wire the motor directly to the AC line without the pressure switch.

Re: Air compressor trouble

#7

Dipstick

Dustmaker Mike

>"I then heard a "pshttt pshttt pshttt" sound that came from the crankase dipstick vent hole, that lasted maybe 20 seconds. The motor was warm enough that I would not leave my hand on it, but it wasn't that bad..."

Just a thought but, you should never see or hear air going by the piston to get into the crankcase. When you turn the air compressor side over does it pump air under pressure? You may have burnt a ring on the pump side also. As for the motor and checking the starting cap I think some suggested to just spin it. Turn it on keep fingers clear and spin away. Good Luck

Re: Air compressor trouble

#8

Re: Just thought of another possibility

Keith Newton

>Since the motor quit without satisfying the pressure switch, the compressed air between the check valve and cylinder was leaking back through the reeds and rings which is why the hissing lasted longer than when the pressure switch drains the pressure off.

But that doesn't have anything to do with your motor problem. When you say "If your reading continuity across the pressure switch" Do you mean that you are getting reading the line voltage before and after the switch?

If you have voltage to there, check it again where it connects to the motor. If it is to there, take the motor in to have it checked, unless there is a button on the end of the motor that you have not pressed to reset after it has tripped from over-heating.

Re: Air compressor trouble

#9

Some answers

Denis Ch�nard, Orl�ans, Ont.

>When I said I get continuity, I meant that the switch (which is still on, as the pressure in the tank is below the cut-in point) works as intended, and delivers power to the two motor leads. Also, when I turn the power on, there's no humming, nothing. This is why I suspect the run capacitor, when my DC conked out, it was the run capacitor that was the problem, and in that case too turning the power on had no effect. And in both cases the machine was running when it unexpectedly died.

My understanding is that if the start capacitor fries the motor still gets power, as it is there as an assist to start the motor. The run capacitor is "on" at all times, and if it dies it creates a discontinuity in the motor circuit. Someone correct me if I'm wrong...

I also did re-set the thermal protection switch a few times, to no avail.

Hopefully I'll be able to check out the capacitors tonight, if family duties allow.

Meanwhile, keep the suggestions coming...

Thanks again,

DC

Re: Air compressor trouble

#10

Re: Some answers

Kneale Brownson in Northern MI

>Are there separate leads for the overheat circuit in the motor wiring? If so, and you can't get continuity between them, the overheat device has failed. I have a similar problem with knitting machine motors (the manufacturer no longer in business) that has been solved by wiring the two overheat protection leads from the control together and the two from the motor together and inserting a fuseholder with fuse between the two sets of wires. The motor shop that advised this approach said rewinding the motor to replace a thermoswitch generally would be more expensive than just replacing the motor. If you do have the separate overheat protection wiring, let me know and I can supply pix of my solution.

Re: Air compressor trouble

#11

Re: Some answers *LINK*

Bill Howatt

>Here are some circuit diagrams. The one you want is #2. As always, these are the typical diagrams but you never know 100% if you might have a variation.

Bill


Motor Circuits see #2.