Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Shop Clutter--- Now where'd I put those...?

Posts

Shop Clutter--- Now where'd I put those...?

#1

Shop Clutter--- Now where'd I put those...?

Dave Morris

>I've got a plethora of small fasteners, hinges, thingamabobs and doohickeys. Piles of boxes of the numerous small things needed for the various aspects of many projects. Good for having them on hand, bad for actually having them "at hand". I find myself spending too much of my limited shop time looking for something I KNOW I have, somewhere.

I need to make a fastener containment/organizer cabinet or rack, obviously. It's kinda like clamp organizing, there's plenty of ways to do it, and most are a lot better than standing the clamps against any convenient wall.

What have you done to replace your piles of boxes stacked on/behind other boxes and clean out your rat-holes of fasteners? I don't have a lot of available wall space, and room for another cabinet is iffy at best. Utilizing part of my existing shop cabinetry might be the best option, but then, that's where most of the fasteners are already located.

Suggestions needed. Short of stealing the local hardware store's nut and bolt display rack, I'd like to organize my fastener storage. What works for you?

Dave-- tired of wasting time looking for things he shouldn't need to waste time on

Re: Shop Clutter--- Now where'd I put those...?

#2

Re: Shop Clutter--- Now where'd I put those...?

Ray

>Two things I use.

1-Those organizers with the small plastic drawers. I find it is cheaper to buy them filled from Harbor Freight than empty from the store.

2-An old tacklebox with moveable dividers.

Neither of these work that well. I also have an old card catalog that I may use for this but every drawer would need a plywood bottom since the metal brackets run right down the middle of each drawer.

http://www.redgreen.com/

Re: Shop Clutter--- Now where'd I put those...?

#3

Easy solution *LINK*

Tom Dunlap in Atlanta

>I was faced with the same issue a few weeks ago. Too many tiny bubble packs, deteriorating cardboard boxes and leaky plastic bags. I was at Northern and picked up a couple of plastic drawer units. The drawers are made from a flexible plastic. They seem more likely to have a longer life compared to the hard plastic units that I replaced.

You'll see several configurations that should fit your needs.

One set of drawer units I bought were sized to fit between sixteen inch on center studs. This made hanging them a snap. Having them between the studs gave the unit some nice support from flexing.

If you go this route be sure to pick up an extra supply of dividers.

I made labels by taking some of my outdated business cards and cutting them down to size. Attaching them with double face tape makes it easy to change the names of the drawers. On some of the drawers I'm going to hot glue one of the fasteners to the front for id purposes.

Have fun sorting and finding treasures!

Tom


Drawer units

Re: Shop Clutter--- Now where'd I put those...?

#4

JL

Re: Shop Clutter--- Now where'd I put those...?

JL

>I am there. I am trying to do something about it. So I am building lots of drawer units.

Re: Shop Clutter--- Now where'd I put those...?

#5

Re: Shop Clutter--- Now where'd I put those...?

Barry Irby

>I have several of those plastic drawer units and also the pack rat gene, so I feel your pain. I also have a number of shop built cabinets with shallow drawers and some not so shallow with lots of deviders. I have a couple of �electrical� drawers and at least two for �plumbing� and one for fasteners and another for sanders and sand paper. ETC ETC

I just had one of life�s epiphanies that in hind site seems rather stupid. If you take out a tool, you create the obligation to put it away. Job is not over until the tools are put away. So getting something out is really at least a two step process. Sort of a Duh! After you think about it. Problem is, I�m about a year behind on the putting it away part.

On a different tact, lately, I have tried to not store so many things. If I bought things I don't use, I take them back. (If I can) I am fortunate to have a Lowes and Home depot within a mile or two. I store my stuff there. Anything that can go back, goes back. I have an endless number of partially used packages and odds and ends, so any unbroken packages go back.

Re: Shop Clutter--- Now where'd I put those...?

#6

Re: Shop Clutter--- Now where'd I put those...?

Stephen Kirk in Quakertown PA

>I user a bunch of those little plastic drawers mentioned above. To make them easier to move around I screwed french cleats to the back and then just hung them on a matching cleat on the wall. Put a bunch of cleats on the wall and you can easily shift things around if you don't like the arrangement.

I also have a portale box that has the smaller plastic cases in it with the adjustable dividers. It works OK but some small things can sneak past the dividers.

Other than that, I second the motion to not collect so much. I only buy in bulk the items I user regularly (standard wood screws, threaded inserts, t-nuts, machine screws, washers and nuts). We tend to use common sizes of things, so you don't need to keep 50 sizes of machine screws with washers and nuts on hand. You can even pick just one style of woodscrew to use as well - phillips, flat tip, square drive or star. Then you only need one set of screw drivers and bits too.

Just keep all your bins labeled. That way, when you start a project it's easy to figure out what you'll need more of.

Re: Shop Clutter--- Now where'd I put those...?

#7

Re: Shop Clutter--- Now where'd I put those...?

Bob Powers

>I long ago developed a foolproof method for storing all doohickeys, thingamabobs, etc. They are all arranged alphabetically behind the frabistats!

Re: Shop Clutter--- Now where'd I put those...?

#8

Re: Shop Clutter--- frabistats!

Carol - Strawberry, AZ

>Frabistats!

What is it?

I want one!

Re: Shop Clutter--- Now where'd I put those...?

#9

Re: Shop Clutter--- frabistats!

Don in Central Illinois

>Only one!! You'll lose just one, we need at least 3 - 4.

Re: Shop Clutter--- Now where'd I put those...?

#10

Re: Shop Clutter--- frabistats!

Carol - Strawberry, AZ

>You're right, Don. My bad. Do you get a discount if you get them in packs of 6?

Re: Shop Clutter--- Now where'd I put those...?

#11

Re: Easy solution

Dave Morris

>That's kinda what I was thinking, Tom... something that would let me stack stuff like it is now, but wouldn't mean moving *everything* to get at that box on the bottom of the pile. Stuff just gets rearranged and out of order too easily that way.

Thanks!

Dave--- Who finds running back to the store for "just a couple more bolts" to be a major bummer, considering the time wasted and gas prices nowadays