Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

OT Car Guy question? Alternator/diodes

Posts

OT Car Guy question? Alternator/diodes

#1

OT Car Guy question? Alternator/diodes

Barry Irby

>My son was on his way back after a visit. His Mazda pickup wouldn't run at full speed but he was able to drive it at low speeds. Went to Auto Zone and they tested the Alternator and declared it good. Still could not go highway speeds so he went to a dealer. They tested it and said one of the diodes had gone bad, thus less than full output. (Got this much info out of a disjointed conversation.....sound familiar, Parents?)

My question is, does this sound right? Diodes? Can you replace a diode or do you have to replace the entire unit? Any idea of cost? TIA

Re: OT Car Guy question? Alternator/diodes

#2

Re: OT Car Guy question? Alternator/diodes

del schisler

>i belive their is what they call a diode plate with the diode's soldered on You replace the plate Or at least that is what i have done that one may be different

Re: OT Car Guy question? Alternator/diodes

#3

Re: OT Car Guy question? Alternator/diodes

Tony - Memphis

>Used to, you could change out a diode. That was a long time ago. I'm not sure if that is still the case. Might be hard to find the parts, dunno. Especially on the import stuff. Google it!

Tony

Re: OT Car Guy question? Alternator/diodes

#4

Re: OT Car Guy question? Alternator/diodes

John E. in SC

>I don't know anything about a "diode" going bad, but what does an alternator have to do with a vehicle "not running at full speed"? I don't think any problem related to the alternator would cause that kind of problem. Any more info?

Re: OT Car Guy question? Alternator/diodes

#5

Re: Few comments

Larry Clinton At Frankfort (Central)., Indiana

>First, one blown diode in an alternator circuit will just reduce the output - battery will gradually go down if you are running lights and other heavy load accessories. I can't see how it could affect the operation of the vehicle unless and until the battery was below 12 Volts - When the voltage dropped low enough to prevent proper spark ignition (or computer operation of spark and / or fuel injection if so equipped) vehicle would die and there would be no battery charge to start it. Second, I have changed the "Diode plate" on at least one GM car. It is somewhat of a hassle, you have to dissemble the alternator, replace the plate, insert a couple of paper clips to hold the brushes back, replace the end cap & bolts and remove the clips. However unless the car in question has an expensive alternator, it isn't worth the hassle. My son & I just replaced his last month on a Chevy full size van, I think the cost would have been around $50 ~ $65 bucks EXCEPT - he had replaced it a couple years ago and it had a full lifetime warranty. Replacing the diode plate would not give you the warranty and likely would cost at least half as much as a rebuilt unit. Not sure of what Mazda pickup he has - or the cost of the alternator. It is not extremely hard to change the diode packs and if the alternator is costly probably will be worth the work. HOWEVER - I don't think that will solve your son's problem. May be a clogged fuel filter etc. - lots of things will cause a car to not run properly - but an alternator would be one of the last things I would look at, if the battery is not running down, I would leave the alternator alone.

Re: OT Car Guy question? Alternator/diodes

#6

Brushes?

Tony - Memphis

>I thought alternators didn't have brushes? I know my old generator on my '54 does. Actually, I replaced it with an alternator recently. Much better now!

Tony

Re: OT Car Guy question? Alternator/diodes

#7

Re: Brushes?

Dan Donaldson

>Not quite brushes in the sense of the old commutators, but they do have slip rings and rotating contacts to feed the rotor.

Re: OT Car Guy question? Alternator/diodes

#8

Re: Brushes? Yep

Larry Clinton At Frankfort (Central)., Indiana

>The stator (rotating member) of an alternator has to have excitation current. Don is correct in that the brushes ride on a slip ring. The old "generators" had a commutator with conductive "bars" connected to the windings of the armature - these brushes carried the entire current of the generator and contact was interrupted when the armature rotated and the brushes moved from one bar to the next. The arc generated then "ate" the brushes and commutator bars - requiring it to be turned on a lathe and the brushes replaced often. The excitation current required by alternators is low and the slip ring is continuous so brushes in the alternators normally last forever. The alternator current is generated in the field windings and doesn't pass through the brushes. Alternators work far better at low rpm's and last far longer than generators.