Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Jet 14" Bandsaw Restoration Finished...

Posts

Jet 14" Bandsaw Restoration Finished...

#1

Jet 14" Bandsaw Restoration Finished...

Dave Morris

>... or more to the point, this old Wood/Metal Bandsaw has reached the level of "working tool" again. Many thanks to the members of this forum for their advice to my questions and the info I found in their posts in the archives.

The saw was a real basket case when I got it, a lot worse than I originally thought. Many things became apparent only after tear-down. The tires and wheel bearings were shot, some rusted parts, a bent lower wheel, the blade tensioning device was busted, no fence, the upper wheel cover was bent and rubbing the upper wheel, the motor mounting bracket was a rusted joke, the base cabinet was all wobbly and weak, the doors on the cabinet wouldn't hardly open (the sheet metal was bent and the hinges were all tweaked), the door knobs were stripped, the wiring was all corroded and totally shot, the original power ON/OFF switch was busted, the blade guides and bearings were all shot, the speed-changing shaft was totally ground up and hanging from it's bearings (NOT good), it was covered in crud/dirt/grime/acid drippings and bird stuff(?), and everything was in a very sad state of repair.

Each time I found something new wrong with the saw, I got more determined to not let it beat me. Dumb? Maybe. Stubborn? Definitely. But in the end I have a better-than-new saw, and I learned a lot more about the saw's inner workings than if I had simply purchased a new tool. But WHY restore an old 14" Jet? Well, I figured I would learn more about what I want and need in a band saw if I restored an old junker. That way, when I have the long green to purchase my "Dream Saw" in the future, I'll be better able to make the right decision for my specific needs. Also, I'll be much better able to determine what condintion a more expensive saw is "really" in, should I buy used.

This saw got a full tear-down, cleaning, all new bearings and (available) parts. Added a link belt and the Kreg fence. Fixed a broken table hand knob with JB Weld (worked great). Reinforced the base cabinet with 3/4" plywood on the inside, designed a new motor mount that slides back and forth for more versatility in blade speed choices, added a 110 volt power outlet for a magnetic task light, and a better switch in a more convenient location. New Iturra Spinner and spring for blade tension. Added the riser block, and removed the locating pins in both the riser block and the lower frame casting so I could adjust the position of the upper frame (now the wheels are pulled "into" co-planer alignment under tension). Had the trashed speed-change shaft replaced (it wobbled a good 45� in what was left of it's bearings, how could somebody continue to use the saw in that condition???) with a new machined shaft and bearings, and it now works perfectly. I had a new guide bar made from some old 15/16" hex stock, since the round bar that came with the new riser block would not fit this old saw. The Kreg fence needed a piece of 1.5" angle stock to mount it on the table, and I filed a slot in the angle stock to clear the table's miter slot. Left the old miter gauge alone, it's resting in it's slot for the picture, but my Incra 1000 will see duty there when it's needed. I fixed the bent lower wheel as best as I could so there is only a couple hundredths of an inch of side-to-side wobble, hopefully that won't be a problem as new replacement wheels are no longer available. Anyway, the saw runs pretty smooth and (barely) passes the nickel test. Still planning on balancing the wheels when I get the time, and a new set of balanced steel pulleys wouldn't hurt either.

Colors are pure Rattle-Can... a coat or two of primer, then Rustoleum Silver Metallic for the frame and table support, Dark Machine Grey for the wheel covers and table sides, Hammered Black for the base cabinet. Left the guides, guide bar, and hand knobs unpainted, but simply cleaned and buffed, and scrubbed/sanded/polished up the table surface just enough to remove any rust, but still leave a little of the old patina. It's an old tool, and I wanted the table to reflect that (or to "not" reflect that, as the case may be). A coat of Johnson's paste wax keeps the surface nice and slick.

This is the first time I've restored a tool, so please forgive any mistakes I've made along the way. Yeah, it took a lot longer than I thought, was more complicated than I originally planned, generated a lot of head-scratching and no small amount of muttered cussing, and used quite a few of the limited free hours I have available for shop time. But was it fun? You betcha!

Now to start making some wood dust. Anybody got some ideas for a folding outfeed table with adjustable support legs? Nothing shows up in a search for bandsaw outfeed tables (lots of tablesaw outfeed stuff though). I've got a bunch of 2-3" thick, 6" wide, 5-foot long curved barrel staves from some old redwood wine vats I'd like to resaw into straight stock for some Adirondack chairs as a gift for my lovely wife. I figure she's earned it after putting up with this project. ;-)

Thanks for looking.

Dave--- who hopes this "Pic" thing works out, since he's never added a picture to a post before


img

Re: Jet 14" Bandsaw Restoration Finished...

#2

Re: Jet 14" Bandsaw Restoration Finished...

Pat Schupbach

>Beautiful restoration!! Be sure to post your first project with your new bandsaw. Thanks for sharing.

Re: Jet 14" Bandsaw Restoration Finished...

#3

Back view of the bandsaw

Dave Morris

>The colors came out better in this picture. You can see the thicker plywood base for the Woodcraft mobility kit. I added an old router table top I made a few years ago, and made the mobile base a little wider than called for to gain a more stable footprint. Ended up being three layers of plywood-- no flex at all. Solved the rattle noise from the foot levelers by adding some wood shims between the pads and the pivot axles, and a couple felt pads where any metal touched metal. Nice and quiet now.

Planned on adding a couple hooks to the cabinet to wind the power cord on, but thinking I may incorporate that item into whatever I come up with for an outfeed table.


img

Re: Jet 14" Bandsaw Restoration Finished...

#4

New sliding mount for the motor

Dave Morris

>Since the old mount was a gonner, I came up with this design to allow the usual vertical and horizontal motor adjustment for pulley alignment. Made from scrap plywood for the horizontal base and vertical motor mount, and scrap oak for the bottom braces. Scrap oak and maple made up the upper mounting bracket, and are bolted to the cabinet top just under the saw through a reinforcing layer of MDF. Parallel slots routed in the base mount and upper bracket allow horizontal motor adjustment, bolts are set in T-nuts imbedded in the cabinet's plywood base, vertical adjustment is through slots on the vertical motor mount. The motor mount base is shaped to fit between the reinforcing corner braces of the cabinet's plywood inner walls (bolted through to the sheet metal cabinet) so it allows as much adjustment as possible when it slides on the cabinet base (floor?).

Good idea? I dunno, but it was all I could come up with at the time and it works.


img

Re: Jet 14" Bandsaw Restoration Finished...

#5

Upper view of motor mounting bracket

Dave Morris

>Hope this pic is clear enough. All in all, it's very easy to adjust the motor since all the weight of the motor is supported by the mount and not my hands.

I plan on adding some holes in the front face of the base cabinet to let the motor get more ventilation. I'm thinking a small household heater register screwed over a piece of filter, and positioned over the holes, will keep excess dust out, prolong the 1 HP motor's life, and look clean from the outside. Thoughts?


img

Re: Jet 14" Bandsaw Restoration Finished...

#6

FANTASTIC job Dave!

Dominic Greco in Richboro PA

>Dave,

Wow, I'm impressed! You really went the whole 9 yards and took this restoration to the next level. I can tell that your passionate about making this a project to be proud of. Cause from where I'm sitting, you should be!

I've also done my fair share of tool restorations. I restored all the tools in my old shop (after the flood of 1999), as well as an old Unisaw, and a Jet 14" Bandsaw. So I have an idea the amount of time and dedication a project like this can take.

Now have some fun and use this saw for all it's worth. I'm sure you'll enjoy every minute of it.

See ya around,

My ugly mug


Dominic

Re: Jet 14" Bandsaw Restoration Finished...

#7

Re: Jet 14" Bandsaw Restoration Finished...

George@Colonel's Workshop-Havertown PA

>Good Afternoon Dave,

I'd NEVER get rid of that saw. Beautiful. Somehow you will get a replacement lower wheel, which after balancing, will require a bulldozer to have a DIME flunk the test. It makes me feel good to see an old tool updated and respected. Very good job. Question? What do you estimate it cost you to restore?

George

Re: Jet 14" Bandsaw Restoration Finished...

#8

Re: Jet 14" Bandsaw Restoration Finished...

Dave Morris

>Thanks Pat. It may be a while before the first project gets done. The combination of limited shop time and certain life priorities usually means project schedules are best measured with the changing of the seasons. First up: giving the shop a good cleaning.

Dave--- wondering how fixing up a single tool can leave the rest of his shop space in such a state of chaos ;-)

Re: Jet 14" Bandsaw Restoration Finished...

#9

Well, shucks...

Dave Morris

>Wow. Thank You, Dominic. Knowing you've had quite a bit more experience restoring tools than I have, that means a lot. I've learned a thing or two reading your posts, and you've given me some good ideas I can use in my situation.

I didn't start out planning to go the whole 9 yards. Initial thoughts were to simply do a quick and dirty "just get it working" job on the saw, but my mindset changed during the process to a "if you're gunna do it, do it the best you can" attitude. Glad the effort was worthy of your kind words. Again, Thanks.

David

Re: Jet 14" Bandsaw Restoration Finished...

#10

The Bottom Line

Dave Morris

>Good Morning Colonel,

Thank you, Sir, for your high praise. Yeah, someday a used wheel will turn up, maybe on an old saw with a broken casting. I'll keep my sensors tuned.

"What do you estimate it cost you to restore?"

Uh-oh... you're going to make me justify the cost? (gulp) Ok, hang on a sec...

(sounds of various piles of tools, bags, spare parts, fastener boxes and half-empty paint cans being shuffled around in the shop as I rustle up some receipts)

Keep in mind my initial desire was to simply "get it working again". My total newbie mindset (read "lack of knowledge" or dumb, take your pick) concerning the true nature of the saw's condition and where to buy parts, was a little naive to say the least. I estimated getting it back in working condition would be a matter of a couple hundred bucks and a few hours work.

Yeah, right. As for cost, this could have been done if I hadn't decided to upgrade certain items like the electrical components (industrial quality parts vs. Borg), or bought a lot of the available parts from Jet (found out after the fact that bearings and tires can be bought for this saw at less than half the price through certain internet vendors). And certain items I consider upgrades to the saw, such as the riser kit, new longer blades, mobility kit, Kreg fence, link belt, and the Iturra Spinner and tension spring, are things I would have added anyway to a bottom-end new tool. All the wood parts were scrap from other projects, so no cost there. I tend to buy nuts, bolts, and other fasteners by the box, so many of those items I either had or was going to buy anyway for other uses. The paint, from a strictly "usability" standpoint, isn't necessary, but the end result does look a lot nicer. Anyway, hear goes...

Saw -- $100

Bearings, tires, and table insert from Jet -- $130

Cost to machine new speed shaft and guide bar -- $40

Power cord, switch, outlet box, and various electrical parts -- $100

Kreg fence -- $114

Iturra Spinner and spring-- $66

Mobile base, Riser Kit, link belt, new blade from Woodcraft -- $192

Paint -- $35

So, I'm into the saw for $370, plus $407 in "upgrades". I probably could have shaved almost a hundred bucks off the saw's total working cost by going with cheaper replacement and electrical parts, but that's water under the bridge.

Of course, there's the time element involved in the restoration, but I tend to look on this as I do my woodworking projects: each one is a learning process I do for my enjoyment. I tend to start something as a simple project, and change my intentions along the way to a more challenging attempt at broadening my abilities. Even the moments of frustration, and there were a lot of them judging from some of my past posts, are part of a learning curve that seemed pretty steep at times. If I was doing this for a living, I'd starve to death.

My wife, on the other hand, thinks the guy I bought the saw from should have paid *me* to haul it off. ;-)

The Bottom Line... was it worth it? I don't have the space right now for a larger saw, so the killer deals I spot on Craigslist such as the "$900 Mini-Max" and the "$1700, 30-inch Oliver" are a moot point. I'm happy with the result. In the end, I guess that's all that really matters.

Thanks again for your kind words, Colonel. Your wit and wisdom have provided me with countless smiles over the years, but your post just gave me with the biggest smile yet.

David

Re: Jet 14" Bandsaw Restoration Finished...

#11

Re: Jet 14" Bandsaw Restoration Finished...

John Cole

>Dave can you talk about how you re-inforced the inside of the base with plywood?, I have a Delta that has horrible flex and was thinking of doing something like this.

Thanks - incredible job!!

Re: Jet 14" Bandsaw Restoration Finished...

#12

Re: Jet 14" Bandsaw Restoration Finished...

Dave Morris

>Thanks, John!

Okay, here goes...

The base cabinet ("Closed Stand" in Jet-speak) was one of those things that looked okay to begin with, but the closer I looked the more problems I saw. The saw could literally bounce up and down by hand on the sheet-metal cabinet top. Some kind of acid had dripped down the sides, some of the machine screws holding the separate panels together were missing, and lot of those remaining were rusted pretty bad. I started thinking about just scrapping the whole base, but decided to try and fix the problem first.

Taking the whole cabinet apart, I cut 3/4" plywood to fit each panel. The panels have "lips" that bolt together, so measuring to fit inside the lips was easy. Then I used a router and/or chisel to remove any plywood that interfered with the machine screws for the panels--- simply notching the edges of the plywood for wrench space. I drilled holes though the metal sides of the cabinet and the new plywood "inner" walls for bolts (four to each side panel). I used 5/16" bolts since I had a couple boxes of various lengths of them lying around, 1/4" bolts would be more than big enough. Same process for the two smaller panels above and below the cabinet door.

Note: Carefully measure the space between the motor's back end, it's pulley, and the cabinet walls (front and back). In my case, the location of the saw's frame meant the motor had to go in a certain spot to keep the lower wheel pulley and the motor's step pulley co-planer, putting the rear of the motor almost in contact with the sheet metal on the front of the cabinet (I was choosing a particular pulley step for a certain blade speed I expected to use most often). This, in turn, meant there was not enough room to leave the plywood panel solid behind the motor. I cut a section out of the middle of the plywood for the front panel to give the motor enough clearance, and it didn't seem to affect the panel's strength. This missing portion is visible behind the motor in the third picture. Your cabinet may be different, or your motor size/location/pulley type may give you more flexability.

All of the side panels were put back together with new machine screws and nuts for the metal lips (#8 x 1/2" screws, IIRC), then I made corner braces for the bottom corners out of some scrap 5/4 oak. They're nothing more than a simple triangle with holes drilled for the 5/16" plywood bolts, with notches cut in the diagonal side, using a Forstner bit in the drill press, to give the nut/washer a level surface. (A hand saw could be used to cut the notches as well.) The size of the triangle braces you intend to use gives the drilling locations for the plywood panel bolts. Mine are only cut about 4-1/2" on each side, but the bolts end up being 3-1/2" in from the exterior corner of the metal cabinet. How so? Well, the plywood makes the walls thicker, so you don't need as large of an interior brace to gain some extra room for the washers and nuts on the long diagonal side on the triangular brace. By now, the cabinet was feeling pretty solid for a box with no top or bottom.

Note: the front and sides of the base cabinet on my Jet are vertical, but the back is deeper on the bottom than the top, and slopes inward, giving the cabinet a larger footprint than the size of the top. On the front corners, a simple vertical 90� cut makes the corner of the brace. For the back corners, one side was a 90� cut on my chop saw, but the other had to be a compound cut on my chop saw. It was about an 11� bevel, IIRC. Again, your cabinet may be different, but I thought I should mention it.

The top was reinforced using a piece of scrap MDF. I thought it would have a nicer appearance on the edge than plywood, and I didn't want to glue some edging to a piece of plywood and have it get partially torn off from use a couple years down the road. You can see the MDF as a layer above the upper door panel in the forth picture. The paint soaked in pretty good, but I made the mistake of not sanding enough on the MDF between coats and you can see it's a little "rough" when you get close. Oh, well, I didn't want it perfectly smooth, it'd clash with the Hammered paint. ;-)

I used the original sheet metal top as a template for size, marked all the holes on the MDF, and drilled them with my drill press. The square holes for the original carriage bolts got cleaned up with a chisel, but then I decided to use hex bolts like the rest of the cabinet and that step wasn't necessary. The opening for the belt was a simple jig saw cut. Problem: The top metal panel of the cabinet had 1/2" of each 90� corner cut to a 45� angle, probably to allow for slop in assembly or prevent a sharp edge, so the MDF panel mated nice to the 90� corners of the sides, but not the top. The MDF corners just looked "unfinished" to me. A few strokes with a file on the MDF at each corner made a nice beveled transition from the 45� top metal to the 90� side metal. The top panel, now metal above and MDF below, bolts though the original holes to the metal sides, but since all the metal parts are now reinforced with plywood or MDF, there's no problem with *any* flex.

The cabinet base is simply 3/4" plywood cut to fit the bottom of the metal cabinet, and bolted to the corner braces. I was originally going to replace the rubber feet on the saw, and didn't think MDF would stand up to the weight of the saw on four small points of contact, hence the choice of plywood. I later scrapped the "feet" idea, removed them, and bolted the cabinet directly to the mobile base, so using MDF for the bottom of the cabinet probably wouldn't have mattered in the end. T-nuts in the plywood bottom secure the motor mount.

All the new parts add some weight to the cabinet, which helps the saw's center of gravity a bit. But the end result is a base cabinet that looks almost factory original from the outside, and is as rock-solid as I could wish, without building an entirely new cabinet from scratch.

Think I got all the details needed. Hope this gives you enough to fix the problem with your saw's cabinet. Working on nuts and bolts at arm's length inside a relatively small cabinet is more tedious than complicated work, but I don't think you'll be sorry for the effort.

David

Re: Jet 14" Bandsaw Restoration Finished...

#13

Re: Jet 14" Bandsaw Restoration Finished...

John Cole

>Wow - great explanation thanks a bunch Dave - I'll have to give it a whirl.

John