Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

cutting foam

Posts

cutting foam

#1

cutting foam

mike mcnerney

>I have a tempur mattress, queeen size, 10 x 60 x 80 & am considering making it thinner, in order to hopefully reduce it's ability to insulate the bodies heat, it's just too hot. I am thinking about getting a band saw blade like the type they use to cut fabric with, or maybe even a 3 tpi & making an 8 ft bow saw. Lay the mattress upside down & build a frame about 5 or 6" high & using that as a guide to saw it.

First question, do you think that will work.

second question do you think it will solve or significantly reduce the heat issue.

third question, how much ventilation underneathe the bed, either holes or slats would help. right now it is sitting on ply with holes on a metal frame, but eventually, I would like to make a box with drawers, knowing I would have to create an airspace of some amount, say 2 to 4". I even wondered about putting some small computer type fans in that space?

The company is useless with advice, they just tell you the waranty would be voided. This mattress is really helping my back problems.

thanks

mike mcnerney in ottawa

Re: cutting foam

#2

Not sure.... Hockey bed?

Mark Goodall - ATL - tooljunkie

>I'm not really sure. I know that you'd get retty wet if it were a water mattress, like I used to have. Of it would be hard cutting through the steel coils in my current mattress. I'm not sure about that type of mattress, but I'm assuming it's just a big flat slab of foam?

"...second question do you think it will solve or significantly reduce the heat issue.."

As far as the heat issue, the thickness of it would only relate to the insulating properies to the cold from underneath. Unless the mattress is sitting on a block of ice, perhaps in the middle of the hockey arena like a true Canadian would have it, slicing the mattress propably wouldn't affect the heat of it.

But I'm not really sure. I only posted this response because I didn't want to pass up the chance to mention a bed on hockey ice.... as a kid that's what we wanted to do, so that we could be the first ones one the ice in the morning.

Happy Woodworking!

Re: cutting foam

#3

Re: cutting foam

Tim Caley - North Little Rock

>I was going to say that I have cut foam with an electric kitchen knife, but on a scale this size I don't think that would be too practical.

Good luck.

Re: cutting foam

#4

Re: cutting foam

Rusty

>Foam saws have 2 blades working in different directions.I have one for upholstery that looks like a jig saw.Electric carving knifes work to.Have you tried adding a pad or some other material on top. I think a red hot wire cuts the stuff to.

Re: cutting foam

#5

Insulation

Tom Dunlap in Atlanta

>It's hard for me to think that you will loose enough insulation by cutting the mattress. It takes very little padding thickness to insulate from heat loss. After spending at least a week per year camping in the snow on the Minnesota/Canada border for over twenty years I have tried a lot of insulation schemes. Using half inch closed cell foam pads was the best option. After the third layer it never seemed to make any difference.

If the bed is becoming a heat sink try and find a way to insulate your body from the foam. A Thinsulate mattress pad would be very easy to make. Add a Mylar backing and you'll have a good combo. The catch is that the Mylar is going to be crunchy and make noise. There might be another high tech heat reflective material out there though.

Tom

Re: cutting foam

#6

Won't Work

Mark Mandell - Gone Round In Jersey

>The bed "sleeps hot" because the material, essentially a block of closed-cell foam, doesn't allow air to pass through it as does an inner-spring mattress. It would have the same effect if it were only 1" thick, so cutting it will only ruin the bed. To get ventilation between you and the foam, use a heavy, fitted mattress pad over the foam. The pad will "breathe" and you'll stay cooler, provided, of course, that you're not under a down quilt in a 70* room |;-}

mm

Re: cutting foam

#7

Re: cutting foam

Craig in Silverdale

>As mentioned earlier, it's closed cell foam. We have a 2" mattress topper of Temper foam on our bed and it made a lot of difference in heat retention. Of course the wife loves that. I would suggest perhaps a sheep skin liner, or a wool pad. Something to put some air between you and the mattress. Either that or cover up with a cold wet bath towel.

Re: cutting foam

#8

Re: cutting foam

Grant Smith

>I'd say you'd be better off buying a feather topper for it. I think that would eliminate lots of your issue.

I haven't wanted one of those for just that reason, but then I am a chronic sweater.

FWIW,

Grant in Iowa

Re: cutting foam

#9

Re: cutting foam

Barry Irby

>My son has such a mattress. He likes his a lot. Believes that a "Sheet" he bought from the dealer is a key pieces of it. It is supposed to take the place of the mattress pad and serve the function of keeping bed wetters from damaging the mattress. It appears to be a thin piece of fabric similar to a fitted sheet. He swears it makes the mattress feel better. (It appears to be a $70 fitted sheet, but he swears by it.)

I would suggest that cutting off part of the mattress will have no effect on how hot it feels and will most probably ruin the mattress. From what I know about insulation, the top inch has about ninety percent of the effect and the second inch about ninety percent of what�s left, at least of the effect you can sense.

I just heard the other day that it is good for you to sleep with the room rather cool and that many people with sleep problems find it beneficial to have the bed room at 68 degrees or cooler. Keeping the room cooler might make the mattress feel less warm.

Re: cutting foam

#10

Re: cutting foam

mike mcnerney

>thanks everyone especeially the canadian hockey fantasy.

Ok so I won't cut it & I guees I will try mattress pad that breathes.

Mike McNerney in Ottawa

Re: cutting foam

#11

Re: I solved the problem on......

Jamie Donaldson

>... my side of the mattress with a foam backpacking pad, probably neoprene. Now I don't awaken in a sweaty ditch, and the "Better half" gets the hip support she likes.