Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

dining table - router jointing

Posts

dining table - router jointing

#1

dining table - router jointing

Clay Foster

>I wandered into wood turning many years ago because I enjoyed the direct involvement with the tree. Twenty years later I�m learning I can have the same experience in furniture making, it just takes a little longer.

I started this table a few years ago when I salvaged an ash tree from a pipeline project. I sawed it into lumber with a chainsaw. One piece was 60� long and 20� wide and about 4� thick, quarter sawn. I cut 4 other pieces 36� long and 5� square to use as legs. There was another 200 bd� in various widths and thicknesses.


img

Re: dining table - router jointing

#2

power planing

Clay Foster

>I got one side flat enough with a power planer for it to lay flat on an assembly table. My jointer is only 12� wide, so I jointed the other side with a router on a sled riding on rails. I routed some grooves to use as depth guides, and then used a power planer to remove wood down to the bottom of the depth guide grooves.


img

Re: dining table - router jointing

#3

one side flat and smooth

Clay Foster

>Then I made one final pass over the entire surface of the board with the router again. I used an upcut spiral bit because that�s what I had that was most appropriate.


img

Re: dining table - router jointing

#4

resawn

Clay Foster

>I do have a 20� planer, so after cutting the board to 19� wide, I planed it down. I ended up with a board about 3� thick, which I resawed with a chainsaw.

After planning the two halves smooth, I had two matching boards 1 1/8 thick. These were glued together to make the table top.


img

Re: dining table - router jointing

#5

Re: resawn

Clay Foster

>The legs were jointed on two sides to get a square edge, and then bandsawn to get a taper. Aprons were planed and cut, and then everything joined with floating tenons. I have a horizontal mortiser, so all the joinery went pretty quick..

All that was a days work. There will be a lot of carving, texturing, burning, filling, etc, which will take weeks. I�ll post more photos as work progresses.


img

Re: dining table - router jointing

#6

Re: dining table - router jointing

Stephen Kirk in Quakertown PA

>A day, wow. That's working pretty hard. That's a very nice board, and I'm glad to hear you were able to salvage the wood. Really nice ingenuity on getting things flat and ready for use.

One question - why did you decide on the having the taper of the legs narrow going up, instead of down? I think I've seen that before, but I can't recall if it's a particular style.

Re: dining table - router jointing

#7

Re: dining table - router jointing

George@Colonel's Workshop-Havertown PA

>Good Morning Clay,

I task like that is fascinating as well as fun. You are doing those old ash boards proud. How long have you been carrying that concept around in your head? Be sure to post the work in various stages of progress. And, Shop Shots afterward. Thanks for that visual treat, which makes the morning.

George

Re: dining table - router jointing

#8

Re: dining table - router jointing *LINK*

Clay Foster

>Usually before I start fabrication I've built the project so many times in my head that it goes pretty fast. Of course, occaisionally my tape measure screws up and I have to back up.

The leg shape is a shape I've been using since visiting the Mayan ruins at Tikal in Guatemala about 25 years ago. It appears in a lot of the stuff I make. You can see examples at http://www.patina-gallery.com/exhibits/current_exhib/07foster/07fostertitle.html


http://http://www.patina-gallery.com/exhibits/current_exhib/07foster/07fostertitle.html

Re: dining table - router jointing

#9

Re: dining table - router jointing

Clay Foster

>George,

It's a technique I first used a couple of years ago when I wanted to make some kitchen counter tops from some pecan I had harvested. The slabs were too wide for the jointer or planer, and hand planing pecancrete was not an option for me.

I've got about 1500 bd' of lumber I've harvested from trees salvaged from construction sites and trees removed from yards for various reasons. I've got a friend in the tree removal business who will save me the trunks. He even has a crane on his truck, and will load the trunks onto my trailer for me. When I get them home, I chainsaw them into lumber right on the trailer.