Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Cutting Sheet Goods

Posts

Cutting Sheet Goods

#1

Cutting Sheet Goods

Lee Beeden

>I need a more accurate as well as efficient method for cutting sheet goods. At present its a skill saw and it seems very clumsy. I've been thinking about purchasing a panel saw; can anyone recommend one? what are your thoughts on the various options for cutting sheet goods; is this the way to go? I realize this may be an investment but i think it will pay for itself!!

Many thanks

Lee

Re: Cutting Sheet Goods

#2

Re: Festool

Joey, Ct.

>Lee; I just bought the Festool circular saw with an extra 55" guide to cut 96" ply. Very smooth cut. The saw felt a little under powered though. Time will tell. I could have done the same thing with a carbide blade on another saw with a straight edge, but Festool has eliminated chip out on the surface of the cut with their design. You could get around that with tape on the cut line. EZ Smart has a less expensive alternative, especially if you already have a CS. Joey

Re: Cutting Sheet Goods

#3

Re: Cutting Sheet Goods

AJ in Ohio

>Lee. If you have the room in your shop[will eat up alot of wall space] a panel saw will do the job. There is a learning curve to ease of operation and to the balancing act with shorter goods. I cut all my plys with a cs [30 year old Rockwell] and homemade straight edges. I made them out of half inch ply, the base piece is 10 inches wide and the rip fence piece is 1 1/4 inches. I screw the rip fence on 1/8 of an inch wider then the table of my cs, run the saw down it and then the st and the saw are the same width. I mark the sheet the size I want,clamp the blade side of the st at those marks, score it with a knife, and cut away. I have a 3, 5, and an 8 foot st. When the st gets a little worn I just move the rip fence a bit. The only problem is they're making sheet goods a lot heavier then they did 40 years ago. At least that is what I tell my self. Art

Re: Cutting Sheet Goods

#4

Re: Cutting Sheet Goods *LINK*

David Yoho

>Lee, The Festool saw and guide system is very good from what I see. However, if you don't have the budget for it right now, you could use the method I use that I documented in Shop Shot #400. It shows shots of me using a router with this setup but it works for a circular saw too. My saw jig block is in the lead picture along with all the various router bit blocks I made. I think the article will give you all the information you'll need if you want to try it. The best part is it doesn't cost much!!

David


Shop Shot #400

Re: Cutting Sheet Goods

#5

Re: Cutting Sheet Goods

Ron Hildreth, Alta, Iowa

>Lee,

Another option and a cheap alternatve is the panel saw kit sold by Rockler, item # 22223. You supply the saw, plywood, and a few other small parts, but it's a lot cheaper than a manufactered panel saw, and kinda fun to assemble. I just ordered one myself and should be here in a week or two.

Hope this gives you another option.

Ron in Iowa

Re: Cutting Sheet Goods

#6

Re: Cutting Sheet Goods

Andy Lincoln,In Dearborn MI

>The idea is an improvement upon using a circular saw as a method to crosscut sheet goods into smaller manageable sizes. For years many people have used a simple guide of plywood to ride the saw against and cut sheet goods. My improvement is the addition of a clamping tool guide to the underside of the crosscut guide .By attaching to the underside the hassles of the clamps interfering with the saw motor is avoided, potential mistakes are avoided by not having to measure/allow for an offset between the tool and the guide, clamping is achieved from one side of the sheet, not reaching over and/or moving to the other side of the sheet.



I sized this guide to 56", which is the length of the Clamp-N-Tool guide(tm), which allows for a clamping capacity of 50". The process and materials could be sized for other clamps (24" and 36") as well as for different manufacturers of clamps. I believe Rockler and Woodcraft both sell a similar style of clamp.


I constructed the guide from birch plywood and used polycarbonate (left over from another project) as a base for the guide. The edge that the saw base rides against is covered with plastic laminate. The guide is attached via screws countersunk from the guide into the birch plywood. The polycarbonate is screwed in place and could easily be changed if damaged. This guide could also be used with a router instead of a circular saw.



Re: Cutting Sheet Goods

#7

Re: Cutting Sheet Goods

Doug Reynolds in Seattle

>I also use the Festool circular saw and guide system but add rigid foam as the support. I lay the foam on the garage floor , place the plywood on top, mount the guide system and cut away. This way I don't have to lift the plywood up on a table. On of these days I'll win the lottery, buy a Felder with a huge swing arm but, until then...

Re: Cutting Sheet Goods

#8

Highjack?, but on topic. Garage wall panel saw.

Craig Daymon

>I'm in a townhouse now and getting a 4x8 sheet downstairs is impossible.

I've been thinking, and this may be something for you to consider, of creating a panel cutting system using the exposed stud wall in my garage. The idea still needs some work, but essentially a tray that would hold the sheets and T-square style cutting guide to use with my Skil Saw.

Of course, I don't want to keep slicing into my studs, so it might have to lift away from the wall about 1/4", unless I restrict myself to vertical cutting motions, which could easily run between studs. I also might want it to be able to clamp the boards somehow, maybe using T-track attached to the sides of studs.

Anyway, I think this idea might handle my panel cutting needs. Is there a chance anyone has done this already?

-Craig

Re: Cutting Sheet Goods

#10

Re: Cutting Sheet Goods

frank shic

>lee, if you really want accuracy, pick a contractor's table saw or a cabinet saw and bolt an exaktor or excalibur sliding table to it. i've tried the plywood home-made rip/cross-cutting guide, the home-made miter seld, the delta sliding table, the eurekazone and i've read many NEGATIVE reviews about the lower-end vertical panel saws like sawtrax. i recently built 14 base cabinets as part of a garage remodel and the parts were square to within 1/32" making assembly and installation a lot easier. if you have the room, a saw equipped with the 60" version of the exaktor or excalibur will give you unsurpassed accuracy and speed for your money - unless you have the money for a striebig!

if you don't have the room or the money, get one of the various guided circular saw systems (festool, eurekazone or even a homemade jig (one for the major rips and another t-square like jig for the crosscuts) to break down the sheets to a manageable size and then finish trim them on a smaller sliding table like the delta or the jessem mast-r-slide. the problem with relying PURELY on a guided circular saw system is that you introduce a level of inaccuracy by having to reference off measured pencil lines.

one of the best parts about using a sliding table like the exaktor is the entire elimination of that extra trimming step.