Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Craftsman 103.23321 Jointer

Posts

Craftsman 103.23321 Jointer

#1

Craftsman 103.23321 Jointer

Terry Alexander

>Fellow woodworkers.

I inherited a Craftsman 103.23321 jointer from my father-in-law. He kept it in the backyard, under a tarp. The jointer itself is in pretty good condition, but as you can imagine, the beds need to be machined to remove the pits and polished. Other than that, I think the unit is solid.

So, I removed the beds and fence and have them at a machine shop where I am waiting for a quote on how much it is going to cost me "should" I decide to go ahead and do the refurbish.

Having said/typed all of that......do any of you out there have an owner's manual for this jointer?

As always......thanks in advance.

Terry Alexander

Re: Craftsman 103.23321 Jointer

#2

Rick L

Re: Waste of money...

Rick L

>As long as the tables are flat there is no need to have them ground. Pits won't make the slightest difference in it's performance. The machine shop could actually do more damage to the tables.

As far as a manual goes get John White's book on machinery tuning from the Taunton Press. That will tell you more than any stock manual.

Re: Craftsman 103.23321 Jointer

#3

close....off by .00001 *LINK*

Sandor in middletown, DE

>Try this link. http://www.owwm.com/files/PDF/Craftsman/103-23320.pdf


103.23320 Manual

Re: Craftsman 103.23321 Jointer

#4

Pits

Mark Goodall - ATL - tooljunkie

>Pits are just tiny "holes" in the cast iron, right? I've salvaged a few cast iron surfaces and just used some fine emory abrasive and WD40 to polish off the high stops and left the tiny holes. The holes don't affect the flatness.

I guess if it's rusty enough, then the hills could affect flatness, but they might just sand off fairly easily.

Happy Woodworking!

Re: Craftsman 103.23321 Jointer

#5

Wax it and go...

John in New Mexico

>I'm with Rick and Mark, my old Delta received similar neglect before I got it, and the pits don't cause any problems. Get rid of the loose rust with emory or steel wool, couple waxings and you're in business.

John

Re: Craftsman 103.23321 Jointer

#6

I have that same jointer.

Neal in San Jose

>It has been a pretty good tool, given it's limitation of a pretty short bed. Anything it can't handle, I do with hand planes. I've never had a manual for it; thanks Sandor! If I can answer any questions, just remove an "o" and shoot me an email.

Re: Craftsman 103.23321 Jointer

#7

Re: jointers

Chuck Lenz

>I have cleaned up two old Delta / Rockwell 4" jointers and ready to do another one this summer. Luckily none of them had much piting if any at all. What I did is bead blast them, buff the machined surfaces with a fine steel wool to bring back the shine, mask off the machined surfaces and labels, repaint the body, then hand rub the machined surfaces occassionally with Johnsons paste floor wax to prevent rust. You'd be amazed how smooth they get.

Re: Craftsman 103.23321 Jointer

#8

You can do a lot...

Rich Glisson

>...with that little jointer if most of your projects are on the small side. As others have said, it's NOT worth having the tables surface ground. I had a similar Craftsman jointer in the same shape as yours (the previous owner had stored it uncovered under his carport). Here is a very easy and quick way to remove 95% of the rust: Take a random orbit sander to the table tops and fence. Start with about 180 grit and end with 320. Sand evenly so you don't make any low spots and don't try to eliminate the all of the pits. Scrub the surfaces down with mineral spirits or lacquer thinner and then wax with car wax. If you don't have an R.O.S. this would be a good excuse to buy one. Note: this is a messy job, so you might want to do it outside or at least connect the sander to a vac. Good luck!

Re: Craftsman 103.23321 Jointer

#9

RUST REMOVER Re: Craftsman 103.23321 Jointer

del schisler

>http://www.theruststore.com/Boeshield-T-9-12-oz-Aerosol-P3C4.aspx check out the page their is another RUST FREE this will remove all the rust and the iron will look like new It was devolped by boeing aircraft I use it and it is the best you can get here is the page for that You can get them at the same place Some wood supplyer's sell it also THIS WILL NOT TAKE THE PITS OUT THEY DONT HURT ANY WAY JUST REMOVE'S THE RUST

http://www.theruststore.com/Boeshield-Rust-Free-845-oz-Spray-P2C1.aspx