Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

minimum sloap for shingle roof?

Posts

minimum sloap for shingle roof?

#1

minimum sloap for shingle roof?

Ernie Miller

>What is the minimum sloap for shingle roof? I'm working on plans for a sun room and need to figure out several things befor going for a permit. first being the minimum slaop for the roof. and will 2X6's be strong enough for rafter if they are on a 16" cinter with a 14' span. This will be a flat roof comming out from the eve of the present house. I want to keep the roof sloap to a minimum as there is only 8'9" from the poured concreet floor to the top of the finished roof line. having the slope more than 1/2" to the foot will have the inside celing getting close to 7'7" or so which is getting a little low at the outside wall of the room. I als have a question about window headers. I will have 5 3' wide windoes right next to each other on the outside loade berring wall would it be better to run a continuse headder clear across the length of the wall or put in individual headers cost is pretty much a wash on that or might even be cheaper if they went clear across. Let me know what you all think or if you have a better idea.

Re: minimum sloap for shingle roof?

#2

Re: minimum sloap for shingle roof?

Bill Tindal, E.TN

>I expect it depends on climate but I have gotten by with 3/12 for a sheep shed.

Re: minimum sloap for shingle roof?

#3

Re: minimum sloap for shingle roof?

Barry Irby

>Ernie, It seems you have three or four questions:

Minimum slope for a shingle roof? The �guarantee� on shingles starts at 4 in 12 and if you get much lower than that you can go to a �Low Slope Application� which requires a double layer of felt and spacing the shingle down to four inch exposure. This is only good down to about 2 in 12. If I read you right, you are at about a � in 12. So the answer is that shingles won�t work. Don�t even try it. Your choices are to raise the pitch of the roof, perhaps by going further up the slope of the roof of you house if that is possible or to go to some type of roofing that will function as a flat roof. (Modified Bitumen Sheet, Brie, tin, Built up roofing, EPDM, etc.)

A very quick look at the local code indicates 2 x 6�s would not be acceptable supporting the ceiling and the roof, assuming there is a �� drywall ceiling. 2 x 8�s would work. (All of this would change if you decide to increase the pitch of the roof and go up onto your main roof.)

You also have issues with insulating and ventilating the cavities in the roof, especially if there is a ceiling attached to the bottom of the rafters.

The headers at 5� 3� would have to be 2- 2 x 6�s.

A continuous header might work, but you have to be careful. The wall has to accept the weight of the roof (down) and the thrust of the roof (out). You don�t want to set up a situation where the continuous header ran all the way across the wall and the thrust caused it to roll off.

The answer is �Check with your local Building Official.�

Re: minimum sloap for shingle roof?

#4

Re: minimum sloap for shingle roof?

Al Stokka - Cambrige, Iowa

>Ernie,

For the receod, what you described is a "shed roof."

�" per foot slope is too flat for even 19" selvege eddge roll roofing. 3-tab shingles require a minimum slope of 4" per foot. Would it be possible to build a gable roof? You didn't mention the other dimension of the room but, if it less than the 14', it may help with headroom while providing more slope.

A 2x6 is good for up to 14'-11" with a live load of 20 PSI, only 11'-4" with a 40 PSI live load.

2x8 will allow 19'-8" @ 20 PSI L.L. and 15'-0" @ 40 PSI L.L.

5'-3" rough opening requires two 2x6 plus on edge. Two 2x10's can span 10'-0, so you'd be borderline. I'd use the 2x6's and trimmer studs between the two windows. You have the window jamb in between in any case and a few additional inches for the trimmers studs should be a big deal. To span the 10'-6" you'll need two 2x12's and it sounds like you're short on headroom as it is.

Al

Re: minimum sloap for shingle roof?

#5

Check with the manufacturer

Curly Smith

>and, of course, your local building codes for the min pitch for an asphalt shingle roof.

However, the typical min pitch is 4/12 for asphalt shingles (I think). I do recall reading somewhere that using the minimum pitch is risky on exposed areas and that you should add 5 degrees to it.

If you really want a low slope roof then you should investigate other roofing choices besides shingles. Singles really aren't viable for a 1/2" per foot pitch, but a "flat" metal roof or poured asphalt roof might work.

I've haven't checked but your proposed rafter system strikes me as substandard. Again, your local building codes will give you the answer.

Re: minimum sloap for shingle roof?

#6

According to the Canadian CMHC tables

Mike in Paradise

>for NO 1. spruce with a 20.0 PSF snow load( which is the lightest snow load in the tables)

you would need 12 inch centers using 2x8's which spans 16'9"

16" centers 2x8 will go 15' 3"

16" center 2x6 will go 12' 2"

12" center 2x6 will go 12' 9"

Minimum application for standard shingles is 1/3 (4/12)

These are from the Canadian Mortgage and house handbook on frame building...

Re: minimum sloap for shingle roof?

#7

roofing alternatives?

Ernie Miller

>What would be a good reasonable alternative for a shed roof? I want to keep cost and maintnance low if possable. What do I look for? DO they make metal roofs that don't have exposed fasteners? I worry about leaks aroung nail or screw holes?

Re: minimum sloap for shingle roof?

#8

Re: roofing alternatives?

Curly Smith

>Just a thought but have you considered polycarbonate? You did say it was a sunroom...

FYI - a quick google search yields this site (strictly for info, no recommendation)

Low pitch polycarbonate roofs

from the URL:

"Complete Low Pitch Non Supported Roof Kits

Low pitch polycarbonate roofs are designed for roofs where you are tight on head room, the polycarbonate sheets for this low pitch conservatory roof system are 40mm thick and reinforced strong enough to cope with a covering of heavy snow. This conservatory roof can be fitted at only 2.5 degrees, Roof projections up to 5 meters available . Available in white or a brown wood grain effect."

Re: minimum sloap for shingle roof?

#9

Re: roofing alternatives?

Ernie Miller

>Dosen't leave room for insulation for the cold winters. But a good idea all the same.

Re: minimum sloap for shingle roof?

#10

Re: roofing alternatives?

Gary Evans Tallassee, TN

>Hi Ernie,

I've had a shed roof on the front room for much of the last 20 years. I have gone through a couple of iterations in that time. The first two go-rounds were using rolled roofing, even though the slope is slightly less than the specified minimum. As I recall, I got 7 or 8 years each time.

The last time we re-did the roof, 3 or 4 years ago, I used metal roofing with screws. While I knew that screws will eventually develop leaks, I also have had good success with sealing over screws on other roofs that I've worked on. I would imagine that applying a little silicone or urethane sealer on each screw during installation would provide a near permanent bond with the metal roof.

I haven't used rubber sheet, but I would imagine that it would be effective for this application, it just wouldn't look very attractive if the roof top can be seen from the ground.

Good luck with your project. Don't fear a low-pitch roof.

Gary

Re: minimum sloap for shingle roof?

#11

Re: roofing alternatives?

John in New Mexico

>The metal roof we used has its fasteners concealed under the next panel, leaving the only screws exposed at the eave and ridge. I think though, that the pitch limitation was something like 3:12 or a little lower.

If you want to go cheap, you can do two layers of 30# felt, nailed or stapled down with tarred seams, then a layer of 40# mineral covered fiberglass felt. Been years since I built one of those, so I'm a bit fuzzy on the details, but they do work for low pitch applications.

You could also go with a rubber membrane roof or one of those spray foam deals, they work for flat and low pitch roofs.

John

Re: minimum sloap for shingle roof?

#12

Rubber (EPDM) would be my choice......

SanMan

>....for anything less than 4/12 pitched roofing.

I would be comfortable using shingles on a roof < than 4/12 ONLY if you used Grace Ice and Water sheild in place of the roofing felt. This is a peel and stick product that will self seal around a nail put into it (ie a shingle nail).

Other low sloped roofing options could be a modified torch down product. Not a big fan of them however.

I would talk with a roofing supplier and get their take on options and new products available.

Bottom line is DO NOT SKIMP on the roof....it protects everything below it.

SM

Re: minimum sloap for shingle roof?

#13

Re: roofing alternatives?

AJ in Ohio

>Why not bring a gable off your house roof? That would solve the pitch , load bearing, and insulation problems. It would also allow you to add lighting, heating and ac vents. You could also cathedral the ceiling which would leave room for fans. It might cost a little more but in the long run [IMHO] you'll be happier.

Re: minimum sloap for shingle roof?

#14

Re: roofing alternatives? Endora - Eudura

Larry Clinton At Frankfort (Central)., Indiana

>Eudora? Not sure of the spelling - The roofing is found at Lowes. I have a addition that was built on to my 120 year old home with a fairly flat roof. I estimate the slope at somewhere between 2.5 -12 to 3-12 pitch. It was covered with conventional shingles when I purchased the house about 40 years ago. I had leaks, replaced the shingles with the best I could buy and they lasted about 4 -5 years before leaking. I installed the Eudora roofing and it hasn't had a problem in the last 6 -7 years. This material is a composite material. It is corrugated and looks somewhat like tile. Comes in sheets 4 or five foot wide and 6 -7 foot long. You can install it right over furring strips, sheeting or over an existing roof. Comes in various colors - literature states it can be painted after aging, but mine hasn't shown any sign of deterioration since installation. I think it has a 50 year warranty, can't remember. It is a little more expensive than shingles, around $50 a square, and requires you to use their flashing over corners, valleys, vents etc. It has foam inserts that close the ends of the corrugations at the eave. I am quite satisfied with both the appearance and the performance of the roof. Might be something you want to look into.

Re: minimum sloap for shingle roof?

#15

Talked to roofing supplier & city building dept.

Ernie Miller

>The roofing supplier suggested a metal roof with a rubber membrain under it screwed and cliped with drip edge and flashing all for about $550 sounds good to me said it was good to .5/12 but wouldn't recomend under 1/12. My wife get a choice of colors. Called the city about the roof rafters/ celing joist. they said we allow 16' span with 2X6 and 2' with 2X4 for these applications? all we really want is for you to pay for the permit and allow us to change your property value. Footing inspection rough in/wiring inspection and final inspection. one inspection every six months at a minimum and if more than three are needed thereis an extra $50 for each additional inspection. sight map and sketch plans don't get carried away.

Re: minimum sloap for shingle roof?

#16

Re: Taking advantage of the opportunity to teach..

Al Stokka - Cambrige, Iowa

>Ernie,

I want to take advantage of your post to teach a few posters that there is a difference in slope and pitch. They are not the same.

Slope is rise over run while pitch is rise over span.

A simple gable roof 24' wall-to-wall with a rise of 4' has a slope of 4/12 but, the pitch is 1/6 (4/24).

One could argue that in the case of a shed roof, pitch and slope are the same, but using slope is never wrong. On the other hand, using pitch when one is actually referring to slope can confuse matters.

Al

Re: minimum sloap for shingle roof?

#17

I've never heard that.

Jason Roehl in Mulberry, IN

>I've been around construction for 11 years now, and know a number of roofers, read several construction magazines, and I've never seen or heard that distinction. Instead, I've always heard that a "10-pitch" roof refers to a 10" rise in a 12" run. Or a "12-pitch" is a 12" rise/12" run, for a "slope" of 45 degrees. As a painter, I know that I can walk up to an 8-pitch no problem, a 10-pitch is a challenge (doable with a handhold somewhere), and a 12-pitch helps me find religion, or some physical aid to walking the roof.

Jason

Re: minimum sloap for shingle roof?

#18

Re: I've not heard that.

Al Stokka - Cambrige, Iowa

>Jason,

Nothing against roofers, but I wouldn't depend on one for a technical definition. As evidence, ask the next roofer you see to name the black sheeting that he uses to start the roofing application. Most likely, he will say "tar paper" or "felt." The proper name is "asphalt saturated roofing felt." No, I don't use the proper term either and either tar paper or felt is fine as long as the term is unambiguous. That can't be said of pitch and slope.

Most likely, your trade has it's own shorthand language. I've not hired a professional painter, being the frugal sort of fellow I am, but I'll bet you use terms that are not technically correct but are generally understood by those in the trade.

Al

Re: minimum sloap for shingle roof?

#19

What I did

Joe Pack

>Not saying it was right, but it has not failed yet.

Faced with a similar situation in 1981, I used heavy rolled roofing first, then put 3 tab shingles over that for appearance sake. I first rolled on a thick coat of roofing tar at the eave, imbedded the rolled roofing in that, rolled more tar over the top portion of the first course of roofing, overlapped the courses of rolled roofing by 12", installed another strip of tar and roofing.... In effect, I applied an almost indestructible weather barrier as a roof to prevent any possible moisture penetration, then put the "show" roof of 3 tab shingles over that. Even if there was water infiltration under the "too flat" 3 tabs, nothing would be damaged except a cracked shingle.

I replaced the roof in 2005, with never a leak or problem.

Again, I'm not saying it was "right," just that it worked like a charm.