Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

New tool...ROS disc life questions

Posts

New tool...ROS disc life questions

#1

New tool...ROS disc life questions

Tom Dunlap in Atlanta

>Now I either have a new 5" DeWalt ROS or one to go with my 6" PC that is in "cloak mode" My tools and shop gear is in my storage unit in boxes. I've been through all of the boxes, I think, and can't recall seeing the PC. Too bad, that is one sweet ROS. So...since I needed an ROS I went to Lowe's and got the variable speed DW.

The project that I'm working on is a coat rack that is being made from a white oak branch. I stripped off the bark with a drawknife and now I'm smoothing things out.

When I picked up the ROS I got a pack of 40 grit discs. Is there a way to tell when the discs are used up? When is is time to change sanding disc/belt/pads in any sander? I'm thinking that there must be a rule of thumb. Or...like a razor blade. when the blade goes back and forth and just scrapes it's time for a new one.

Any help?

Tom

Re: New tool...ROS disc life questions

#2

Re: New tool...ROS disc life questions

Al Stokka - Cambrige, Iowa

>Tom,

I like your analogy of a razor.

Paying attention and comparing the speed of wood removal to a new disk is the best way. If, on the other hand, you go into a daze while sanding, like me, you'll just suddenly realize that the sanding is slower than it should be. That kind of fun actually, because when you do install a new disk, it cuts like magic.

I also, on the rare occasion that I pay attention, notice that I put more pressure on the sander to make the abrasive cut as the disk becomes worn. When I wake up, I realize that it's time for a new disk.

Al

Re: New tool...ROS disc life questions

#3

Re: New tool...ROS disc life questions

Phil Joines Krum,TX

>It dulls faster that you might think. One of the pro turners, I forget who, has a saying: Use sandpaper as if someone else is buying it.

Re: New tool...ROS disc life questions

#4

Re: New tool...ROS disc life questions

Carol - Strawberry, AZ

>That's a Wally quote, Phil.

Re: New tool...ROS disc life questions

#5

Re:ROS disc life questions - Ooops!

Carol - Strawberry, AZ

>I'm on the flat side, so you may not know Wally.

He is Wally Dickerson, from Arizona. Thin walled hollow form turner extraordinaire, and been at it over 70 years.

Re: New tool...ROS disc life questions

#6

Dale Lenz

Re: When it quits making dust or...

Dale Lenz

>make a pencil mark on the wood and it takes a "long" time for the mark to erode away. Long is def. longer than it should take, : ' >, say 15-20 seconds or so.

Re: New tool...ROS disc life questions

#7

Re: New tool...ROS disc life questions

Barry Irby

>I have been sanding some heart pine and find it clogs the sand paper almost instantly. This started with my Performax. One pass through and the belt is clogged. At $8 a pop, this was too expensive. Someone here suggested washing them. I did, in Simple Green solution and it worked great. I this case the sandpaper was clogged, not worn out or dull. I tried it on sanding disks for my ROS also. Since they appeared to be paper and not cloth I basically dipped them in the solution for a minute or two and brushed them off with a toothbrush. It worked fairly well but two things happened, the rest of the stearates (white powder) came off and they curled up into a tube. I think they will still sand reasonable well but not as good as new. So, if your green oak is clogging them more than dulling them, you may be able to clean them.

Dulling is a whole different topic and you will have to learn to judge. Dull 120 is not the same as 220. Wally is right. Drive 'em like you stole 'em. Dull sandpaper can be awfull. It tends to sand away the softer part of the grain faster than the harder part and will not level the surface. If you see someone's project with a rippled surface following the grain, one reason is they may have used dull sand paper. You should level the surface (or sculpt) and remove tool marks with fresh sharp coarse sandpaper. Every grit after that just removes the grit marks left by the preceding grit and really should not remove much "wood".

Re: New tool...ROS disc life questions

#8

Back to making little...

Tom Dunlap in Atlanta

>...bits out of the big one today.

Thanks for the insights.

Barry...there are some waves developing so today I'm going to change the discs a bit more regularly.

Re: New tool...ROS disc life questions

#9

Quick sharpness test

JRutter

>It is subjective, but works for beardless me. Touch the sanding grit to your face. The sensitive skin can tell the difference between sharp and used up grit. Just be sure to stop the sander first ;-)

-JR

Re: New tool...ROS disc life questions

#10

After about five minutes of use. (NM)

Doug Reynolds in Seattle

>

Re: New tool...ROS disc life questions

#11

Thanks, Barry --

Brint in Atlanta (soon to be Richmond)

>...didn't know that about the ripple/grain correlation in sanding. That's helpful.