Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

making a tub inclosure

Posts

making a tub inclosure

#1

making a tub inclosure

Ernie miller Topeka ks

>any one ever made a tub surround for a jacuzzi spa tub? we are wanting to put in a sun room with a tub in the corner and was wondering how hard it is to make the inclosure? My wife wants it to have a tile surround but we also have to make access room to the punp and watter. any plans or ideas?

Re: making a tub inclosure

#2

Not too hard...

John in New Mexico

>I've done a couple, got one in progress right now. Tub is supported underneath on the floor or a pedistal if you want it elevated a bit, so you just have to get within 1/4" or so below the rim and then caulk it in. Worst part is caulking the sides near the walls if its that kinda tub.

You got the tub yet? Got a shape in mind? The design commitee here prefer's oval tubs, so I get to futz around with curves on the base. Last one we plastered, this one will probably be oak bead board, though I'd prefer to plaster it too. Some tubs have the base surround as part of the casting (or whatever you call the molded fiberglass), with an access panel built in. The one we've got this time requires a panel figured into the design, but its easy enough, just going to make it look like a nice little door.

John

Re: making a tub inclosure

#3

Re: making a tub inclosure

Bill Earl

>We put one in the master bedroom suite. The tub-deck and surround are all tiled over 1/4" HardiBacker. Under the deck is stuffed with fiberglass insulation for heat retention and to muffle the pump noise. Service access is via a gasketed hatch on an outside wall, so there is no direct sound-path to the tub-area.

Build the deck and floor to handle the load (about 8 pounds per gallon plus occupants). Tile-work does not tolerate much flex, so a little over-engineering doesn't hurt.

Pump-noise can be annoying, but make sure that your sound-proofing allows for sufficient ventilation around the pump.

Re: making a tub inclosure

#4

Re: Not too hard...

Ernie miller Topeka ks

>wwe are looking at several differant two person corner models. it will be going into a new sun room the tub will be in a corner with an exhisting bath room on one wall and a outside wall on the other. it will be on a concreet slab so it will be elivated slightly to make the plumbing easier. One of the tubs we are looking at sells a skirt but it is $500 more and I think it would be easier &cheaper to build one well cheaper any way. it would also make for a step into it.

Re: making a tub inclosure

#5

One thing to look at...

John in New Mexico

>They've got a new(ish) type of tub, that just blows air out little holes rather than circulating water through the jets. Supposed to be quieter and much easier to keep clean (we used to do bleach washes on the last one to get the scum out of the lines). No idea yet how well they work.

I think you're on the right track with the skirt, cheaper to build it, and it looks better too. With a corner unit, the skirt will probably be straight pieces, so not too hard to build. I've been doing a framed mini-wall with 3/4 cdx top that then gets a skin on the sides and top. We've done teak for the top, and the latest will be walnut. If you did some kind of frame and panel sides, you could make them a little big, scribe to fit and just attatch to the structure behind that holds up the deck. Make one hinged for access, or even just with some brass screws, as you rarely need to get in there anyway.

Sounds like an interesting project you got going!

John

Re: making a tub inclosure

#6

Re: One thing to look at...

Ernie miller Topeka ks

>I have to get the sun room built first. 14'X16' off the master bed room. I'm wanting tile floor the wife keeps pushing for other options. I will win that battle. we will probably put marble on the suround. Still don't know what to use for a roof. sinse it will be a 12-1 or 1.5 sloap I don't want to use shingles but don't know how to transition to metal.