Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Dado Blades can be dangerous

Posts

Dado Blades can be dangerous

#1

Dado Blades can be dangerous

Matt Berry

>Since I'm such a big stickler for safety, and I think accident reports are an important reminder / learning lesson for others. I wanted to share my tablesaw mishap with everybody. The tablesaw in question is an underpowered craftsman direct drive contractors saw which can normal be stalled in most situations.

Yesterday I had a couple of rails that were 2 1/2" x 13" x 1 1/8" thick that I wanted to rip a dado 5/8" wide x 3/8" deep down the center of the edge, to accept a flat panel.

On the first rail I started the cut, and the little voice in my head said wonder if this piece is long enough to make it over the dado blade and still be supported by the throat plate (my dado throat plate has a space to the front and rear of the dado blade). So I stop the saw and do a mock run through, everything looks ok. Still not 100% confident with the cut I start the cut again, watching it very carefully ensuring the piece didn't tip or pull away from the fence.

as the front of the part made it just past the half way point on the dado blade, POW, the part kickbacked, peeling back a layer of skin on my thumb and "jamming my thumb" pretty good, there was a little bit of blood but nothing major.

So what happened? Well as the part went forward the force of the dado blade caused the nose of the rail to tip forward (no side to side movement) the gap in the throat plate behind the blade added to this threat, and allowed the blade to dig into the wood and launch it.

How could this have been prevented, well there are a few things that could have been done differently.

1. Use a longer piece of stock to cut the dado in then cut to length (not quite an option here since this was 4/4 stock finished planed to 1 1/8" thick a feat in itself)

2. Make or use a zero clearance insert for the dado blade, could have also constructed a sled or jig to give the part more support.

3. Use the tablesaw for what it was truly made for to hold lathe accessories, and or hand tools. Let this be a lesson to all other turners out there don't deviate from a tools true use.

4. Probably should have been using a push shoe from the beginning of the cut.

Ok, so what went right, well, no amputations or contact with the blade. Why, well here are some of the reasons why.

1. never have fingers in a direct path of cutter, (especially if applying pressure twords the blade) whether hand is in front of or behind the blade.

2. Stance, well balanced, so if piece isn't there I won't lunge forward into the blade.

3. Cutter safety zone, I have a safety zone around the blade where I don't allow my hands or fingers go into.

My thumb is still a little sore from being jammed but I expect it to be better by tomorrow. I just hope this helps someone else be safe.

Re: Dado Blades can be dangerous

#2

these posts are valuable, and a comment

Bill Tindal, E.TN

>It seems that most table saw injuries involve small parts and often small parts that are under the "control" (or not) of push sticks. I know of several in the club.

This well written post has fixed in my mind the high risk of sawing small parts and the poor control one has of these parts with just push sticks.

If you are sawing something small with an aggressive blade hands may attacked by flying objects.

In addition to the suggestions provided by Matt, I do the following. I keep a zero clearance insert in the saw. I used an 8" thin blade (it is vastly less graby than the typical 10"). And I never (except for night before last when I got nailed by a small flying piece) use a push stick to control small pieces.

Re: Dado Blades can be dangerous

#3

Re: Dado Blades can be dangerous

Chuck Lenz

>In most cases I use a push stick. I once apllied for a job at a shop that makes cabinet doors and the owner of the company was ripping a board to 2 1/2 wide. He said I I don't need to use a push stick when doing that. I don't work for people that push people that way. Needless to say after seeing that, I wanted no part of working for that company. I was a meat cutter for 17 years, and a woodworker for close to 30 years and I still have all my fingers, COMPLETE. I plan to keep it that way.I'm surely not going to lose one working for a poverty wage while the boss gets rich. I hate pushy people.

Re: Dado Blades can be dangerous

#4

Re: Dado Blades can be dangerous

The Ink Man

>It's funny how often that little voice in our heads is a harbinger of things to come. The more posts like this I read, the more I tend to pay attention when that voice says "watch out." Appreciate the post and the heads up.

Re: Dado Blades can be dangerous

#5

Re: Dado Blades can be dangerous

Tom Stockton

>I'm glad your not hurt. I really don't like dado blades and am real happy I have a saw that won't take one. there are usually other ways to cut the groove you need that are safer and as fast. I saw someone doing plunge dados get the tip of his thumb chewed up and have really avoided them ever since.

Tom

Re: Dado Blades can be dangerous

#6

Excellent Safety Post...

Jim Dillon

>... and I'm glad you came out unscathed, but I bet that thumb hurts. Thanks for taking the time to tell us about your "adventure".

Jim

Re: Dado Blades can be dangerous

#7

Re: Excellent Safety Post...

Matt Berry

>Last night it did, today it's not too bad, still don't have full mobility back yet with out any pain but it is getting there. It's still swollen a little bit too, but no discoloration.

The part that really sucks about it is it has really cut into my shop time and kind of limited what I can do today. No getting the bookshelf done today. :(

Re: Dado Blades can be dangerous

#8

I quite understand

Brian In Dawson Creek

>I�m a little confused � regardless of the gap between the front and back of the blade to the throat plate, wouldn�t enough support be provided by the by the wood between the blade and the fence and a push shoe (not push stick) was directing force toward the fence? I don�t understand how the piece could have tipped.

What if the user had wanted to make a shallower cut using the same throat plate, this would increase the gap between the front and back of the blade to the throat plate, but still wouldn�t enough support be provide by the wood between the blade and the fence.

So for every dado blade height change should one make a dedicated zero clearance throat plate?

To further muddy the waters, Bill Tindall says he never uses a push stick while Chuck Lenz says he does

In the diagram below I think I�ve shown Matt�s setup � if I�m wrong please correct me. As an alternative could not a sacrificial fence been used, then the work piece could have been butted right up against the fence.

I hope someone can clear this up for me as I would like to continue to use my dado blades safely

Thanks

Brian


img

Re: Dado Blades can be dangerous

#9

Re: I quite understand

Bill Howatt

>He had the workpiece centered on the dado blade, ie, the dado was down the middle of the workpiece but I think your diagram shows what likely happened but this depends on the dimensions of the workpiece and the opening in the dado blade's tablesaw insert.

He might have had the left edge of the workpiece on the left-hand opening in the insert. As he went forward the bottom left corner of the workpiece dropped into the opening causing it to catch. If you are using pushsticks or even a shoe the downward pressure is at the tail-end of the work.

A rough examination shows that on my TS with a workpiece of those dimensions and my stock dado insert with approx a 1-5/8" wide opening this could happen.

There is no mention of featherboards or similar devices being used so there may have been a slight bit of rotation from the fence causing the blade to dig-in - it doesn't take much! Featherboards are always good especially with short stock.

Short pieces are always a potential safety problem on the TS.

A good thread pointing out some safety issues and it does us all good to be reminded about safety and hazards.

Bill

Re: Dado Blades can be dangerous

#10

Re: I quite understand

Matt Berry

>Close except for the orientation of the work piece. The piece of wood was 2 1/2" x 13" x 1 1/8" thick. The dado was through the center with the 1 1/8" side face down. So that gave approximately 1/4" support on either side of the cut. with the slight gap on the sides and the back of the blade it allowed the piece to pivot down into the blade and shoot it back with a lot of force.

I've looked at the part a couple of times, and there is no sign that the piece twisted to cause the kickback. I can see at the top(bottom?) of the dado where the blade dug in deeper (first 1" of the cut) and didn't clear the chips but transfered the power to the piece instead. Did the saw slow down for a split second with the additional load? I don't know.

I do know that I will be using zero clearance insert when ripping dados on any shorter board. I'm thinking about clamping a 1/4" sheet of plywood to the tablesaw, and use that for a zero clearance insert.

Re: Dado Blades can be dangerous

#11

Re: I quite understand

Matt Berry

>You are correct, no featherboards were used in the making of this accident. They may have helped reduce the force of the kickback but I'm not sure that using ones along the side would have eliminated it completely. I had one hand holding the part against the fence, and the other one was directing the forward and down pressure. Since it was at the beginning of the cut I hadn't started using a push shoe yet because my hands were not in the danger zone yet.

The part could have rotated side to side a bit, but I didn't see it twist away from the fence prior to this, and the marks in the dado itself do not show any damage to the sides, only damage is to the bottom where the dado blade got a little grabby and that seems to be even across the width.

Re: Dado Blades can be dangerous

#12

Re: Dado Blades can be dangerous

John Pappas

>Matt, I don't know just what might be considered a safe amount to cut in a given pass, but a 5/8" by 3/8" dado is probably more than I would have attempted in one pass. I tend to take light passes with router bits and dado blades. In this case I probably would have made two passes to get the depth of 3/8 inch. Also agree with the idea to use a shoe rather than a push stick. Thanks for the post.

Re: Dado Blades can be dangerous

#13

clearing my part

Bill Tindal, E.TN

>I don't use push sticks on small pieces with the table saw (I do on the band saw where small things are sawed when I can). They simply are too unreliable for controlling small pieces as evidenced by the many people I know that have gotten hurt trying to control small pieces with push sticks. I do use a push stick for ripping longer pieces and in these cases the stick is used for pushing the last foot of the piece past the blade.

Note I said stick, not sticks. I don't use sticks for any operation. If I can't control the piece safely with at least one hand on the board I find some other way to saw it.

My Delta saw has the old Delta fence which has one big advantage over the modern fences. When ripping, this narrow fence is nestled between my 1st and 2nd finger. My thumb is hooked over the end of the piece being sawed, pushing it forward while my hand slides along the fence. My 1st finger is pressing down on the piece to keep it from riding up. This arrangement constrains my right hand from getting over the blade and this hand is not apt to leave this configuration in response to something unexpected. My left hand thumb is also pushing the piece forward as well as into the fence and my left hand fingers are also pushing down. My left thumb dangles down and when it touches the edge of the saw my left hand stops pushing. Occasionally this left hand will pick up a stick and help shove the piece forward, especially if the piece is wide to the left of the blade. (this description is for the fence to the right of the blade)

So yes I use a push stick for pushing, but only under conditions where the other hand has good control of the lumber. With the fingers of my right hand locked over the fence I am comfortable sawing strips down to about 1 1/2" wide with out a push stick, especially if the blade I am using is not putting a lot of force on the piece (which will be the case if a narrow kerf small diameter blade is used). I saw with the blade barely sticking above the piece being cut.

The bottom line is that to prevent kickbacks, the most common injury I have seen with table saws, one must maintain reliable control of the wood by what ever means you can come up with.

Re: Dado Blades can be dangerous

#14

Re: clearing my part

Brian In Dawson Creek

>Thanks Bill, and every one else. This was a good learning thread for me.

Brian

Re: Dado Blades can be dangerous

#15

Re: clearing my part

Chuck Lenz

>I guess you can't please everyone. Just use some common sense when working with power tools. Think about what your doing first.

Re: Dado Blades can be dangerous

#16

Re: Dado Blades can be dangerous

brad bransky, lawrence, ks.

>About the same thing happened to me a couple years ago. Now, my Featherlocs and I are very good friends.

When dadoeing:

1. I use three Featherlocs. One in front of the stacked dado blades against the left edge of the piece, one behind the blades set to touch the piece as it passes by the blades and one atached to the fence against the top of the piece so it can't raise up.

2. I use an insert 3/4" wide and long enough to cut a groove no deeper than about 3/4" deep. Any deeper or wider, I use the router or make repeated passes with the single 64 tooth Forrest blade and chisel the bottom smooth.

3. I make a few shallow cuts each deeper than the previous and slowly push the piece with a wide handle Moby Stick. Slow and shallow always!

I ain' takin' no more chances, no way!

Happy bandaging,

Brad

Re: Dado Blades can be dangerous

#17

Zero clearance is easy

Larry Marker in Alabama

>Making real zero clearance throat plates for every dado size would be tedious, but there si a real simple way -- especially for small pieces -- just carpet tape a piece of 1/8" fiberboard to the table and raise the dado blade up through it.

As for push sticks, et al -- i hate push sticks -- they don't give me enough control. I used to use shop made push shoes, but now I use a pair of Grr-rippers. Best darned safey gadget in my shop!

Larry

Re: Dado Blades can be dangerous

#18

Re: Grr-ripper makes this a safe cut

Larry Clinton At Frankfort (Central)., Indiana

>I run a lot of dado's using the set of Gr-rippers I have. I have made a few slots in the rubber boots on the Gr-rippers due to improper setup or feeding them through the opposite direction they were set for but they eliminate kickbacks and really make handling thin and/ or short pieces easy and safe. I will never be without them in my shop. No affiliation - just a very satisfied user.

Re: Dado Blades can be dangerous

#19

Re: I quite understand

Bill Howatt

>I believe that placing a couple of featherboards beside the workpiece to hold it against the fence so it can't rotate is more important than hoping they will stop kickback if the blade catches. Yours is an interesting case since most kickback, IMO, is caused by workpiece rotation/pinching causing the blade to catch the side of the cut.

Glad you posted your experience and you weren't hurt more seriously. I know I will be paying more attention the big hole in my stock dado insert.

Bill

Re: Dado Blades can be dangerous

#20

ditto

Joe Piotrowski - Chicago Burb's

>