Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

OT Truck Running Boards-Long

Posts

OT Truck Running Boards-Long

#1

OT Truck Running Boards-Long

mdclor

>Hi!

I greatly appreciate the collective wisdom here. I have purchased a new Tundra truck (stealth gloat)! I need running boards or something for LOML to easily get into it. This hasn't been an issue previously, so my questions are:

1. Are there significant advantages/disadvantages between running boards, step rails or NERF bars and steps?

2. It seems that NERF bars don't require drilling. Is that true and do they have adequate strength?

3. Are there any manufacturers that are great or that should be avoided?

4. I am not a mechanic or mechanically inclined, so will I need the recommended product to be professionally installed?

Any responses will be greatly appreciated.

TIA,

Merle

Re: OT Truck Running Boards-Long

#2

Re: OT Truck Running Boards-Long

Rob Sandow

>I've had NERF bars on mine for 6 years. They are plenty strong and since they have no paint, aren't subject to the same kind of wear that running boards are. Have them professionally installed.

Rob

Re: OT Truck Running Boards-Long

#3

You can have mine

Dustmaker Mike

>this is the first truck that I have ever owned that had any kind of running boards on it an I HATE them. When I step out I hit them when I get in I hit them they hit the back of my pants and leave dirt marks on them when I drive the truck to work. My wife thought she would use them and I find her avoiding them because of the same reasons.

My other truck had a 2" lift under it and my wife would just grab the handle and get one cheeck started then slide in. Now she bangs her head cause she steps on the stinking running board. Nope when I get a Chance they are off the truck to the recycle yard. The trucks I have owned have all been F150s so these will not fit yours.

Depending on where you live what type of weather and the type of roads you drive on may make a differance also. You want ones that drain the water out of the holders(supports)and the dirt leaves with it. Mine are soild brakets and hold water and dirt. They are the half round type not sure of the correct name.

Re: OT Truck Running Boards-Long

#4

Whats your 10-20 ?

Scott in Eastern Iowa

>FWIW

If your in an area where you will see alot of gravel road driving or in the upper Midwest in a state that uses salt on their roads, then I highly suggest you go with stainless steel for the material.

Most are 304 stainless and really arent much more than the others.

My boss has a set of 2 yr old black powder coated ones on his truck and they have rusted thru already.

What a waste....Nothing like throwing away 300 bucks I guess.

Scott

Re: OT Truck Running Boards-Long

#5

I've got the 10" Carr steps on my Dodge

Don Henthorn

>and like them. I would rather have a smaller truck since mine has the twenty inch rims but my wife who is old and short loves the truck. She couldn't get in without the steps. I broke one of the steps on a rock and now I am trying to find a replacement without having to buy a whole set.

Re: OT Truck Running Boards-Long

#6

Re: OT Truck Running Boards-Long

Clay in Illinois

>I had black powder coated Nerf bars on my truck, they only lasted about 2-1/2 years. Big waste of money.

Re: OT Truck Running Boards-Long

#7

Re: OT Truck Running Boards-Long

Dave Morris

>A lot depends on what you want them for. If it's just so the LOYL can get into the truck easier, then a simple step pad or short nerf bar under the door (single cab) will do. For a four-door truck, a pair of nerf steps or a longer bar will fit the bill. If you want easier access to the bed as well, longer bars or an extra bar for the bed will help.

Me? I went with Ultra Board stainless running boards from front wheelwell to back wheelwell on my 4x4 crew-cab long bed truck. I'm not going to blaze any extreme off-road trails in this Conestoga Wagon (I had a Bronco for that), so loss of ground clearance wasn't a concern. But I have a raised camper shell with a lumber rack surrounding the shell on this truck, and the rack covers the whole four-door cab as well. The front to back running boards let me access cargo much easier since the load is so high off the ground, no matter where it is tied down. It's a 1997 truck, and the running boards have held up perfectly during these last ten years. But that was what fit the bill for my needs. Get the style that fits your needs and your taste in appearance.

Just remember, anything strong enough to support a person getting into and out of a vehicle needs to be *rigidly* attached to the frame of the vehicle. This doesn't mean you have to have a Pro do it, but it usually does mean you have to drill a few mounting holes in the frame for the board support braces. No big deal, you can do it yourself, or the dealer can do it for you in an hour or so. But as in many things, you get what you pay for. Get something that will last at least as long as you anticipate owning the truck.

Oh, and, BTW.... Congrats on the new rig!

Dave--- who thinks running boards were one of the best things he ever bought for his truck

Re: OT Truck Running Boards-Long

#8

Look under your truck!

Jason Roehl in Mulberry, IN

>At least some of the newer trucks these days actually have mounting points for NERF bars or steps or whatever. If so, getting the right ones for your model can be a simple bolt-up. My old '93 F250 doesn't, so the wheelwell-to-wheelwell running boards that came with it were all cobbled together with angle iron underneath. I've got the bed sections already off, and the fronts are going to come off as well, but I do want to get something under the bed again so I can reach over my tool boxes into the bed.

As far as looks, I think the stainless NERF bars look the best (or a similar product). Running boards just collect dirt, snow, and more dirt.

Jason

Re: OT Truck Running Boards-Long

#9

Nerf bars

John Ergle in SC

>I've got chrome Nerf bars on my '04 Dodge ram, and they are really a help for the wife and kids to get in and out. I personally would not want anything with paint or powder coat - too easy to chip. One thing I remember when I bought them - you want the "steps" pressed into the tube, to cut away (sorry if that doesn't make sense - ask the salesman) - cutting a section out of the tube lets water get in and makes them more likely to rust. I don't think mine required any drilling (I didn't install them), and are very solid.

Re: OT Truck Running Boards-Long

#10

Re: OT Truck Running Boards-Long

mdclor

>My thanks to everyone. There are some great points here that I hadn't considered. I've had trucks for years but haven't needed running boards before. I think I will go with the stainless NERF type.

Merle

Re: OT Truck Running Boards-Long

#11

Carry a step stool!

Paul in NJ

>