Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

electricity

Posts

electricity

#1

electricity

Mike H

>Help--------I was installing our new dishwasher and know I am worried that I hooked up the white wire to the black and the black to the white neutrel wire. How dangerous is this crossing wiring. I am not looking forward to having to pull the washer out and doing the work over.

Re: electricity

#2

Re: electricity

Bob Fawcett

>I would say do it over. The white neutral in 120v power is usually grounded in the box and the black is hot. The DW is hooked to plumbing and that can be ground also. You have the possibility of a direct short or worse a hot dishwasher.

Re: electricity

#3

Re: electricity

Brian Gaynier

>No Choice but to fix it, otherwise you risk electrocution. 120 VAC can kill; all it takes is 100 milliamps.

Sorry to sound so dramatic, but many people don't realize the danger that 120 VAC can present.

Brian

Re: electricity

#4

Re: electricity

Jim Swank

>Pull it out and fix it. If the ground is connected properly, it shouldn't shock you, except if you screwed up black and white, you better check the green too. If nothing else, you'll sleep much better...

Re: electricity

#5

Re: electricity

Mike H

>Thanks everyone for your help. Yes, I will certainly pull the DW out and do it over again.

Mike

Re: electricity

#6

Re: electricity

Bill Turpin in WNC mountains

>Most certainly fix it. On 120 vac devices all the safeties are in the hot line: over-temp, water level before heating element, etc. With reverse polarity a short can allow things to still cook, spin, etc. even though they are turned OFF. This is not only a shock hazard but also a FIRE hazard. When your house burns down the insurance inspector will decline coverage because of improper installation!

Bill in WNC mountains

Re: electricity

#7

Re: electricity

mdclor

>And I thought it would just run in reverse and make the dishes dirtier.... Shows you what I know! ;)

Merle

Re: electricity

#8

:-)

David Yoho

>

Re: electricity

#9

Re: electricity Dc motors would run backwards

del schisler

>only DC notors would run backwards And AC you would have to have the winding's inside change FIX it

Re: electricity

#10

Re: electricity

Barry Irby

>I don't even know what diswhasher you are woring on, but all the ones I have ever installed could be wired in place through the kick plate. At least enough to check the wiring and see if you had to pull the DW. And yes, I would double check and correct it.

Re: electricity

#11

I dunno. Clean dishes in; diryt dishes out?

Forrest Addy

>Seriously, shoulden't be a problem so long as your ground wire is also connected to the D/W frame.

Re: electricity

#12

Re: I dunno. Clean dishes in; diryt dishes out?

Bill Howatt

>I also don't think it is a real problem but as always, the ground must be connected. However, it would bug the heck out of me until I changed it.

There may be a slightly better level of safety with it hooked up the "correct" way something like putting the neutral wire of a lamp on the outer shell connection. We went many years with lamps where the non-polarized plugs could be inserted either way such that putting the neutral on the outer shell was just a gamble that the lamp would get plugged in that way.

I agree with another poster that there likely is an easy way to get to the connections without pulling the whole thing out.

Bill

Re: electricity

#13

Re: electricity

Mike H

>So this morning with my wife's help I pulled out the DW and opened up the electric box and to my relief I had not cross-wired it. The white wire connected to the DW white wire and the black wire connected to the DW black wire.

I checked the ground and it was good and tight to the frame. A lot of work but I feel better about it,

So thanks everyone for your comments.