Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Lumber storage question...

Posts

Lumber storage question...

#1

JL

Lumber storage question...

JL

>I've finally got all my tools in one place - and my lumber. The tablesaw and bandsaw will not be operational until they get down from the garage and into the shop.

In my previous shop I used the heavy duty angle brackets "nailed" into the cinderblock wall with the lead anchor nails. This worked fine for short pieces.

I have a larger shop, still with cinderblock walls. I was thinking of the Lee Valley Lumber Storage System (http://www.leevalley.com/wood/page.aspx?c=2&p=32145&cat=1,43326). This way I wouldn't have to build anything and I could get things in order more quickly. I would go for a 16-24" spacing

Other "immediate" alternatives would be the Rubbermaid or Closetmaid garage shelving systems. These aren't as strong, of course. I could also build shelves, but they wouldn't be as adjustable.

Thoughts?

Re: Lumber storage question...

#2

Lee Valley system gets my nod

Charles R. Smith

>Some years ago, I renovated an old two-car garage to make it into a woodshop, and replaced the 2x4 inch walls with 2x8 inch walls (yeah, overkill, but it was fully insulated to keep me toasty warm during cold Ontario winters). I installed the Lee Valley system along 20 feet of one wall using huge lag bolts, starting two feet from the floor and extending 10 feet high. It was sufficiently solid that you could use it as practice for mountain climbing. And the flexibility made it relatively easy to alter shelf widths in response to my changing wood inventory. It gets my nod.

Charles in Victoria (whose workshop lacks long walls for lumber storage)

Re: Lumber storage question...

#3

Re: Lumber storage question...

Dick Krieger

>I am a true "make it myself" kind of guy. Building lumber racks that specifically meet your dimensional requirements and are adaptable to changing needs makes a lot of sense to me. I would start with attaching 2 x 4's to the cinder block wall. Instead of using lead anchors, I would use toggle bolts put into the block webs. The tendency of lumber racks is to present some "side pull" to your attaching point. Probably 5/16" or 3/8" would do. Then, with a good base, you could build any type of adjustable or non-adjustable racks for your storage. Just a thought and my 2 cents worth.

Dick

Re: Lumber storage question...

#4

Re: Lumber storage question...

Glenn Madsen near San Francisco

>Well, those work, but so does a frame of tubafors from the Borg...

My problem is that I hobby/work in a two-car California garage, and change my storage & tool configurations a bit. Well, the lumber rack doesn't move much, except in a largish earthquake. Right now, it's ballast, loaded down pretty much to the max with good stuff I can't seem to get into the production cycle.

Pretty cheap, though. The bolts cost almost as much as the boards.

And the hand tool shrine hangs on the wide side. ;)

Re: Lumber storage question...

#5

Two ways....

Mark Goodall - ATL - tooljunkie

>I use 2" angle iron... bolted/welded and then lag bolted to the wall. The trick is if the vertical piece extends down to the floor, it will support a ton of weight.

If you want a faster approach, HomeDepot sells these almost-industrial grade shelving... not quite as hefty as the stuff the use themselves for their items (and you probably used in your warehouse) but but heftoer than anything else available. Think t's called the Z-fold shelf. It's about $109 for 6' x 18' and 6' tall and 4 (or is it 3) shelves. Very quick and can hold many tons.

Happy Woodworking!

Re: Lumber storage question...

#6

Charles....

HC Sakman

>...I thought your "lumber storage" is outside, in big chunks for rounding furthermore. Isn't it?

Chico...

PS:I'd come and see your place one of these days...

Re: Lumber storage question...

#7

Re: Lumber storage question...

Howard Norman-Prescott, AZ

>I have the Lee Valley storage system that you referenced. It is sturdy and strong. It isn't cheap but I am very satisfied with it. My shop is in the basement and I have it fastened to an outside concrete wall. It gets my vote.

Howard

Re: Lumber storage question...

#8

Re: Lumber storage question...

Roy Fleming

>I recently installed closed maid shelving and currently have 250 bf of qs oak on the shelves and all seems ok. quite a bit cheaper tha lee valley and is good enough for my needs

Re: Lumber storage question...

#9

LV's is tough, 2x4's are cheap...

John in New Mexico

>I had the LV system in my garage in Tucson, usually with about 600 bdft on it, maybe a little less (about 2000#), and attached to a 2x4 framed wall (ends sitting on the floor of course). But if the price is prohibitive, there are lots of good ways to make a heavy rack out of framing lumber. You might also try a surplus store if there's one around. Theres a couple in Albuquerque that have all sorts of neat stuff rusting away in the yard (of course, there's a big AFB right there too, so bound to be good surplus).

Re: Lumber storage question...

#10

Re: Lumber storage question...

Brint in Atlanta

>I have the Lee Valley system installed in the shed I just built (okay, have almost finished building -- but really, I'm almost done!!) and, like Charles, have found it very handy to use as steps up into the eaves to store things and retrieve them (not to mention storing about 200bf of rough cut sweet gum and tupelo). In fact, I like it so much that when we leave here in a month to move to Richmond, VA, I'm taking it down and taking it with me (after, of course, I finish the shed -- and really, it's almost done!).....

Re: Lumber storage question...

#11

My Wall Rack

Mike Fitterling

>There are several store-bought rack systems that would do the job, but in less time than any of them would take to arrive you can make a simple, inexpensive rack yourself. Here's a diagram of mine. I have made three of these systems so far and they are very strong. All it takes are 2x4s, some �" galvanized pipe, some PVC, and screws. I attached mine to studs 16" on center, but in your case you would have to use anchors. I made one of these for my new lumber storage building the other day and it took about 3 hours.

Good luck with whatever you choose. Cheers,

Mike


img

Re: Lumber storage question...

#12

Here's a Photo of the Rack 

Mike Fitterling

>


img

Re: Lumber storage question...

#13

Purty nice jointer there Mike, what is it?

John in New Mexico

>

Re: Lumber storage question...

#14

JL

Re: I guess you can have too much lumber :)...

JL

>Thanks for the idea and the diagram. That looks like something I can do with my portable tools. Though I don't promise to drill an exact 2 degrees.

Re: Lumber storage question...

#15

Re: I guess you can have too much lumber :)...

Mike Fitterling

>No, you will probably need a drill press and a helper to hold the end of the lumber to do that. If you do it by hand, you will probably not have even supports.

Cheers,

Mike

Re: Lumber storage question...

#16

Jointer

Mike Fitterling

>That was the find of a lifetime. I got it (along with my DC) from a stair manufacturer who was going out of business. It is a Northfield 12" and was in running condition when I picked it up. All I needed to do was build a rotary phase converter and change the knives (It came with two extra, sharp sets.). Got it for $500! It was made in 1959, but they still make the identical model, now selling for around $11,000!! I love that machine and it sure makes work easier. Added bonus is lots of times I can skew the fence on narrower stock and for edge jointing and get cleaner cuts with less tearout.

Re: Lumber storage question...

#17

Re: My Wall Rack

Jim in Fenton, MI

>This is something I need to do as my wood has outgrown my storage. How long did you make the pipes? They appear to be the same length from level to level.

Thanks..

Re: Lumber storage question...

#18

Re: Lumber storage question...

Ken Garlock, Collin County Texas

>Hi JL

I installed "DorFile" brand shelf and standards; I believe DorFile is a brand name or division of RubberMaid.

I used the 70" long standards with 12" brackets. The standards are screwed in to the garage studs with 3" #14 secrews. They ain't coming off. The standards are spaced every other wall stud. I wouldn't e afraid to put my Wife's anvil collection on the setup.

I bought mine at Lowe's.

Happy shelfs,

Ken

Re: Lumber storage question...

#19

Re: My Wall Rack

Mike Fitterling

>I made the supports about 15" long. with 2�" in the 2x4, that gives 12�" sticking out. I cut up pipe and whatever was left (in the case of the shop rack it was 12" lengths) I used for a shorter row, so not to waste them, on the top of the rack where big boards are hardier to pull down anyway.

Re: Lumber storage question...

#20

Re: Lumber storage question...

NickB

>I have the Lee Valley system on 2 walls of my concrete-walled basement. Works great for me. I've seen a shop-made wooden analog. Vertical members (has to be something hard like oak) bolted to the wall, with a series of square mortises, and shelf members that fit pretty tightly into the mortises (no glue).

Nick

Re: Lumber storage question...

#21

Rust or any marks left

Dustmaker Mike

>I am wondering, outloud of course. Do you have any problems with discoloration on the wood on the bottom or against the pipes? I made one from 2x3s from one of the borgs. Which works fine in the basement but I may be moveing soon and I am not sure of what type of shop or how big a shop I will end up with, so this may work in the next place.

Re: Lumber storage question...

#22

Never mind I should read slower(-;

Dustmaker Mike

>

Re: Lumber storage question...

#23

Look in the Shop Shots....

SanMan

>.....for a fella named Grant Smith.

He's got a winner very similiar to this posted there with a detailed diagram of how to assemble what he's done is in an article, with room behind for plywood storage too.

SM

Re: Lumber storage question...

#24

Link *LINK*

Mike Fitterling

>That is very similar except for the plywood storage. Good twist on the design if you have room to the side to slide the plywood out. Of course, it will also take up some more floor space in front of the rack.


Grant's Article

Re: Lumber storage question...

#25

JL

Re: Too many choices... Thanks

JL

>Grant's and Mike's design both look like winners as does the Lee Valley. The Z-Fold shelves looks real good for heavy duty storage and I'll definitely keep them in mind for the garage and shed. I'll cost them all out. I figure the Lee Valley system would run me about $200 for what I need right now.