Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Need help with cabinet

Posts

Need help with cabinet

#1

Need help with cabinet

Danny Wells

>I'm building a laundry cabinet for a friend. It's 84"h x 33"w x 21"d. I have the case done. It is going to be installed in a room that was formerly a patio, so the floor slopes in the direction of the width of the cabinet, thus the cabinet will have to be shimmed up considerably. It will have two doors using Blum euro hinges. Should I install the doors first or wait until I have the case in place and plumb?

One other question. What is the best way to cut the doors to width so I get a reasonable gap and even gap. The case is square and plumb in my shop, but it may be difficult to get it exactly plumb where it is going to be installed.

Never built a cabinet this big before. Thanks for any suggestions.

Re: Need help with cabinet

#2

Re: Need help with cabinet

Pat Barber

>If you have the room at the top, build a scribed base out of

2x4 that you can make level. Set the cabinet on this base

and wrap the base with 1/4" material. Hang the doors "after"

you get the cabinet square and level.

I don't understand the "door" question regarding width...

Re: Need help with cabinet

#3

Re: Need help with cabinet

Danny Wells

>Thanks Pat,

What do you mean by a "scribed" base.

I guess the question about the width of the doors was just in case I couldn't get it exactly level and cabinet was skewed slightly. Getting it level and plumb will take care of the that.

Re: Need help with cabinet

#4

Re: Need help with cabinet

Kris Lasure

>If you are using euro hinges, you have a good bit of adjustment to align the doors once you set the cabinet and reinstall the doors. Did you build a face frame or frameless cabinet? I get the impression you probably built a frameless box. If that's the case I'd use a gap between the doors of 4mm (5/32") and 2mm at the edges. I actually prefer the look of 3mm gap, but if your case is a little out of square, the extra mm will give some play for alignment.

I always build separate toe kicks for cabinets of this nature. Usually out of 3/4" exterior grade ply and 4" tall. If the subfloor slopes as bad as you say, build the toe kick to match the slople, then your shimming will be minimal and you have a perfectly level base to set your cabinet on. It's alot easier to shim a 4" toe kick rather than wrestle an 84" tall box.

Re: Need help with cabinet

#5

Re: Need help with cabinet

Charles Sharp

>He's describing a loose toe kick.

It can be made out of 1" or 2" material. You make a box to fit under the cabinet, shim it until it's level then take a compass and scribe it to the floor. Cut the scribe line and it should sit level.

If your cabinet has a partition, put a cross brace in your toe kick below it. If you use a cross brace, cut a small arc in the bottom, otherwise you'll have to scribe it also.

Re: Need help with cabinet

#6

Re: Need help with cabinet

Mike Turner

>I would suggest the attached (see link)adjustable legs for your cabinet. you can get 1" or more adjustment which should take care of your sloped floor. The clips that come with the legs attach to the back of your toe kick boards which then clip tp the adjustable legs...

http://www.ikea.com/webapp/wcs/stores/servlet/ProductDisplay?storeId=12&langId=-1&catalogId=10103&productId=36260

Re: Need help with cabinet

#7

Re: Need help with cabinet

Bob Lang

>Once you stray from straight, level and plumb you're in trouble no matter what shape the room is in. The advice so far about a loose toe kick that you can level separately and fit to the floor, or the abjustable feet is the way you want to go. Hang the doors with the cabinet level in your shop, and they will fit right when you get the cabinet level in the field. Any other approach will leave you guessing and the doors won't look or operate the way they should.

Bob Lang

Re: Need help with cabinet

#8

Bob Lang's Answer is Right On

Howard G

>

Re: Need help with cabinet

#9

Re: Thanks guys....

Danny Wells

>I really appreciate your responses. This has been a real head scratcher since I'm not a cabinet maker, but ya'all have gotten me on the right track. The loose toe kick makes a lot of sense in this situation, and I understand the scribe idea. I've seen that done before. I like the idea of the levelers, and had not seen that brand before, but don't think I have time to order them. I'll have to do the scribe.

Thanks again, I knew I had come to the right place. I'm usually over on the woodturning page.

Re: Need help with cabinet

#10

Re: Need help with cabinet *LINK*

Jim Dillon

>Danny,

Here is another source for the leg levelers like Mike suggested. I've used the Blum levelers on kitchen cabinets and was pleased with how they installed and worked. The removable toe-kick has come in handy as well. If you don't already have it, Woodworkers Hardwares's catalog is worth getting. And as Kris said, your Blum Euro hinges do indeed have a lot of adjustment built-in. Good luck.

Jim


Blum Leg Levelers

Re: Need help with cabinet

#11

Another thought...

Jim Dillon

>... since you said you don't have time to order the adjustable legs. Rather than build the classic leveled floor-box from 2 x 4s, you could just scribe the sides of your cabinet directly (well indirectly actually). Cut yourself a piece of plywood, say 6 inches high by 21 inches long (the width of your cabinet). Place that on edge in the exact spot where one of your cabinet sides will stand. Level it front to rear (shim if necessary to hold in place) and then scribe. Transfer that to your real cabinet side. Do the same for the other side. This way you avoid having to lug your rather large cabinet around.

Keep in mind you burn your bridges behind you when you scribe the actual cabinet. If your client wants to move the laundry cabinet to another location (or house), the scribed sides may not fit and the cabinet might not be level. This is why adjustable legs are a nice alternative.

Speaking of adjustable legs. Rather than installing the adjustable legs directly to the bottom of the cabinet (or lowest shelf), you could fasten the legs to a separate piece of plywood cut to fit inside your cabinet. Level the plywood, then slide the cabinet onto the plywood and add a nice toekick. The downside to this method is that you will be left with a gap between the floor and the sides of you cabinet; a piece of side trim might be necessary depending on how fussy your client is. Just some thoughts.

Jim

Re: Need help with cabinet

#12

Re: Finally its done

Danny Wells

>Thanks for all your help guys. I did order the leg levelers. That worked great. Followed your advice about getting it plumb and square in the shop, and it's plumb and square installed and looks great. Here's how it turned out. All plywood construction and all glued up except the gussets and the hinges. Kick plate is not installed yet.


img

Re: Need help with cabinet

#13

Re: Finally its done-Pic 2 

Danny Wells

>


img

Re: Need help with cabinet

#14

Re: Finally its done-Pic 3

Danny Wells

>with the clothes hamper tilted out.


img

Re: Need help with cabinet

#15

Re: Finally its done

Fred West in West Chester, PA

>Danny, great looking job. How long did it take you and what did you use for material? Fred

Re: Need help with cabinet

#16

Re: Finally its done

Danny Wells

>Fred, I had 46.5 hours in it including the install. That seems like too much to me, but I'm not totally set up for cabinet work. It is all birch plywood except the stretchers at the top and bottom and the gussets in the top corners. They are red oak. The plywood is called China birch because it's imported from China. Most of the lumber yards around her in Louisiana carry it. I love the Blum hinges. Its the first time I've used them. I'll certainly use them again.

Re: Need help with cabinet

#17

Whoa, that is...

Jim Dillon

>... one BIG cabinet Danny. Very nice job and I like the laundry pull-out. Thanks for showing us the final product.

Jim

Re: Need help with cabinet

#18

Re: Finally its done

Bob Lang

>Nice work Danny, great idea with the gussets at the top.

Bob Lang