Hand Tools Archive

Subject:
cultural thing...
Response To:
Misprint? ()

David Weaver
..when you get over toward ephrata PA and north, south, east of it, there are one-man and "a few man" shops everywhere (many larger than that making chairs or kitchen cabinets).

At the consumer level (tables and chair sets for $1500, for example, or bar chairs for $300 each), there isn't much evidence of hand tool use.

If there are smaller shops catering to higher-end customers (repair, carving, restoration), I wouldn't be privy to those, but would be curious about how many of them are building furniture (for a living) using mostly hand tools.

FIL and I went through a few chair and table makers' shops, and there was definitely not a single hand cut dovetail in any of them, but in one of them, the proprietor (a mennonite fellow who sold only amish-made furniture - as in, he didn't make anything, just owned the shop) said something along the lines of one amish guy having an automated dovetailing setup and most of the drawers in his shop were made by that guy on one machine. He implied that the guy dovetailing the drawers made nothing but drawers - and the rest of the bits were made by another shop.

Messages In This Thread

Light vs Heavy planes
Re: Light vs Heavy planes
I like tools from Brooklyn
Re: I like tools from Brooklyn *NM*
Infills in the UK
I'm glad you commented.
Weight Comparison
more infill weights
Re: more infill weights
initial fitting...
one more follow-up comment.
Re: one more follow-up comment.
rosewood
Re: rosewood
Re: more infill weights
now there is a pearl of wisdom
Re: I'm glad you commented.
what I've found...
Re: what I've found...
Re: Calling BS
Re: Calling BS
Re: Can't argue
Re: Calling BS
by the early 19th century
Re: by the early 19th century
It's not offered as ball court...
Re: It's not offered as ball court...
I'm guessing on parts here...
I miss Todd Hughes' contributions too *NM*
Re: Calling BS
Re: Calling BS
I think we're agreeing...
Re: I think we're agreeing...
Re: Me too
Wood isn't indefinitely stable, either
Re: Facts, not assertions
Re: Facts, not assertions
I haven't seen it....
Re: I haven't seen it....
Truing Kanna
expanding on what jim said
Re: expanding on what jim said
Re: expanding on what jim said
Coupla thoughts
different methods of lapping and the bump
Re: I haven't seen it....
Re: I haven't seen it....
Re: I haven't seen it....
interesting that...
Note on a modern infill
konrad's planes...
new vs. old planes...
Re: Light vs Heavy planes
Turnover, newbies and FAQ
comment on teaching
If you get my drift...
finding out who to listen to...
Re: finding out who to listen to...
Re: finding out who to listen to...
I agree...
Re: Same
Old history
Misprint?
Re: Misprint?
cultural thing...
Shops using mostly hand tools..
Re: Shops using mostly hand tools..
Don felder's guitar...
Re: Light vs Heavy planes
Not a positive contribution to the discussion
Re: Light vs Heavy planes
Inertia and figured wood
Re: Jim, what is Osae-gani? *NM*
Osae-gani
Re: Osae-gani
Note on fitting
biases for the maker...
Re:wedge fitting
Re:wedge fitting
funny...
Re: funny...
At some point..
The experiment and conclusion are both confusing
Re: Heavy and light
another factor
If you're trimming furniture...
The best case for heavy planes...
Re: reframing the issue
Friction, and more
Re: reframing the issue
not the direction I went *PIC*
5 1/4
Re: Light vs Heavy planes
Re: Light vs Heavy planes
Re: Light vs Heavy planes
Re: Light vs Heavy planes
© 1998 - 2017 by Ellis Walentine. All rights reserved.
No parts of this web site may be reproduced in any form or by
any means without the written permission of the publisher.

WOODCENTRAL, P.O. BOX 493, SPRINGTOWN, PA 18081