Hand Tools Archive

Subject:
Re: realize significant gains???

David Weaver
I just don't remotely understand the ardent recommendation of imai chisels at a much higher price than a lot of other chisels tied in with this sudden reversal that not only do carving tools need to hold their edge even better, but that tools that have less edge strength than mediocre japanese tools are just fine.

It doesn't make a lot of sense to me.

Carving tools and chisels definitely not the same. I would prefer "old steel" carving tools, but I don't do a lot of carving. Like warren says, I tend to mind the edge when I do have to do it.

A chisel that can be sharpened in 30 seconds on diamonds (or a plane iron, same - except maybe a minute or two if there is some camber) is not the same as a carving tool.

When 3v is the standard steel used for high quality chisels in 10 years, I suppose there will still be people hacking away at this, but it makes no sense given a lot of the prior discussion - as i said - about how people should not buy low-level japanese chisels, but instead spring for the blacksmiths that do more work on the metal at the forge.

I still choose the chisel that holds the edge the longest and works at a nice angle if I go at it again. I won't go at it again, unless my stuff burns, but were I to do it, that's what I'd do. I'm open to new smoothing irons, though, always. I have plenty of mediocre irons that I'd love to replace with an iron that is both long wearing and chipout resistant (chipout really irritates me in planes, either in old brittle irons or new steels with large carbides).

My chisels are O1, old cast steel chisels and white #2 (presumably all of them are white #2, and not #1). I think that covers all of them, except the D2 mortise chisels - I much appreciate those. several swipes on a polish stone after each mortise and there is no need to break down and hone the chisel for an entire project, it's just as easy as stropping.

But, anyway, what is the reason for the sudden disconnect? Certainly there can't be any reason to push $100 imai chisels over iyorois or whatever the $50 cheap flavor of the day chisel is if 3V is suddenly excess because of one peter follansbee demo.

Messages In This Thread

CPM 3V vs. CPM M4 ?
Aaaaaaaaaaahhhhhhhhhhhhh!!!!!!!!!!!!!!!!!!!!!!!!!!
Re: Aaaaaaaaaaahhhhhhhhhhhhh!!!!!!!!!!!!!!!!!!!!!!
Re: Aaaaaaaaaaahhhhhhhhhhhhh!!!!!!!!!!!!!!!!!!!!!!
Re:Length of thread
Re:Length of thread
How do you sharpen your nib,Marv? *NM*
Re: How do you sharpen your nib,Marv?
What good would a short answer do? :D *NM*
Yet another new metal (long)
Priceless
Way to go Bill !
(Message Deleted by Poster)
Re: Sticks and stones... sounds like woodworking
(Message Deleted by Poster)
Re: Bravo!
(Message Deleted by Poster)
Re: Bravo!
Christ all mighty...
Finally!
So...
Your moderator, reading this subthread... *NM* *PIC*
But Bee-wee,we wuv you...
Re: But Bee-wee,we wuv you...
"...but I know he does..."
We do what we can
Re: CPM 3V vs. CPM M4 ?
that is the problem
Re: CPM 3V vs. CPM M4 ?
Re: CPM 3V vs. CPM M4 ?
Re: CPM 3V vs. CPM M4 ?
Re: CPM 3V vs. CPM M4 ?
Re: CPM 3V vs. CPM M4 ?
Re: CPM 3V vs. CPM M4 ?
Re: CPM 3V vs. CPM M4 ?
to repeat a chisel dulling discussion
Re: to repeat a chisel dulling discussion
Re: CPM 3V vs. CPM M4 ?
I`m just happy...
Wait...
Metals
Re: Metals
must consider the whole process
Re: Metals
Re: Metals
As my dentist once said...
Bring on the Novocaine! A brief missive.
Cr-V question, then...
Re: Cr-V question, then...
realize significant gains???
View from the peanut gallery
In a nutshell (well, for me, anyway)
hardness, toughness
Re: hardness, toughness
could you explain the numbers?
You bet.
Re: You bet.
Re: You bet.
Re: You bet.
Re: You bet.
Where on earth? What on earth? Huh? Say whuh?
Since when has mass acceptance and ...
Re: Since when has mass acceptance and ...
Those are the numbers! *LINK*
Re: Those are the numbers!
I'm confused, Warren
Re: I'm confused, Warren
Re: Those are the numbers!
I'm impressed!
Re: I'm impressed!
"Sherman, set the Way Back machine for... "
Re: "Sherman, set the Way Back machine for... "
Why diamond wheels aren't used to grind steel
Re: diamond wheels - that's what I was after
Grinding Temperatures
Steve knows stuff.
Diamond wheels? Who brought up diamond wheels?
Re: Diamond wheels? Who brought up diamond wheels?
Your closing line reminds me of Dan O'Neill,
There I went again.
Re: There I went again.
Well, I was thinking about a diamond wheel. :) *NM*
Re: The diamond and HSS thing...
Re: The diamond and HSS thing...
Re: The diamond and HSS thing...
It's not so much a file protection thing as a... *LINK*
Just out of curiosity,
Re: Just out of curiosity,
Re: Just out of curiosity,
Re: "Sherman, set the Way Back machine for... "
Can you expand this thought Warren?
Good catch! *LINK*
Aim Hardness for 3V
Interesting and valuable *LINK*
3V Heat Treatment Schedule
Very helpful, Steve
Cryo
"How ya gonna keep 'em down on the farm... "
The good stuff
I like bacon. :@) *NM*
Re: I like bacon. :@)
Gotta agree Warren
Re: The good stuff
Re: The good stuff
Re: "How ya gonna keep 'em down on the farm... "
Heat treating -- the simple and not so simple
Re: Heat treating -- the simple and not so simple
Tom's right, Pam -- but wait! There's more! *LINK*
Re: Tom's right, Pam -- but wait! There's more!
Re: Tom's right, Pam -- but wait! There's more!
Re: Tom's right, Pam -- but wait! There's more!
Steps to completion
Thanks, Bob, understood. *NM*
Re: Tom's right, Pam -- but wait! There's more!
Work hardening?
Re: Work hardening?
Re: Tom's right, Pam -- but wait! There's more!
"All your base are belong to us"
Re: realize significant gains???
BTW #2
Re: BTW #2
Suggestions Larry? *NM*
Let he who is without sin...
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
A model for decision-making
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: realize significant gains???
Re: Bring on the Novocaine! A brief missive.
Hi, Andrew! (and a couple things I left out above)
Re: Hi, Andrew! How do they make ...
Here ya go, George. *LINK*
Re:Thanks David, now I know.... *NM*
Different worlds,different approaches
Re: As my dentist once said...
Tow truck? Who needs a tow truck? *LINK*
Re: Tow truck? Who needs a tow truck?
Oh, see? I handed you a straight line back :D *NM*
Re: Metals
Re: Metals
Re: Metals
Re: Metals
Re: CPM 3V vs. CPM M4 ?
© 1998 - 2017 by Ellis Walentine. All rights reserved.
No parts of this web site may be reproduced in any form or by
any means without the written permission of the publisher.

WOODCENTRAL, P.O. BOX 493, SPRINGTOWN, PA 18081